Results 1 to 8 of 8

Thread: Advise Please On D2E Lifted Pad Solder Point B Wiikey 2 6 Wire

  1. #1
    Junior Member
    Join Date
    Aug 2008
    Posts
    33
    Thanks
    3
    Thanked 0 Times in 0 Posts

    Advise Please On D2E Lifted Pad Solder Point B Wiikey 2 6 Wire

    I've gone and botched up a straight forward install and need some advice please. As you can see from the picture I have lifted the pad on Solder point B whilst attempting to install a wiikey 2 6 wires on a D2E.



    Is there a fix for this? Do I go straight to the pin that the trace leads to? Or am I snookered?

    Thanks
    Last edited by madchester; 11-25-2008 at 02:03 PM.

  2. #2
    New Member §piktsµ's Avatar
    Join Date
    May 2008
    Location
    Orlando, FL - USA
    Posts
    548
    Thanks
    6
    Thanked 24 Times in 22 Posts
    Go straight on the pins... and it will work...

  3. 1 User Says Thank You §piktsµ For This Useful Post


  4. #3
    Junior Member
    Join Date
    Aug 2008
    Posts
    33
    Thanks
    3
    Thanked 0 Times in 0 Posts
    Thanks for your quick response.

    I thought it would work but wanted to hear confirmation from a PRO like your good self first. Before I got stuck in. I really must lay off the heat I think, I'm getting a little over confident!

    When I first lifted the pad it came loose, but did not disconnect from the trace leading to the black resistor (If that's what it is) and the wire was still connected to the pad. So I put some more solder on it to make sure of good connection, a little too much solder possibly, and fired up the wii. I ran the update disc and all was working fine, playing backups etc, but the Wii was having problems with the eject mechanism. I didn't think It was a short. I assumed it was the botched "B" pad.

    Anyway, I will solder to the pin and just hope that that ejecting issue was a cause of the "B" pad being lifted.

  5. #4
    New Member §piktsµ's Avatar
    Join Date
    May 2008
    Location
    Orlando, FL - USA
    Posts
    548
    Thanks
    6
    Thanked 24 Times in 22 Posts
    Welcome.. and i hope it all goes fine once you are done.. =]

  6. #5
    Junior Member
    Join Date
    Aug 2008
    Posts
    33
    Thanks
    3
    Thanked 0 Times in 0 Posts

    Job Done!

    Thats it. Finished. I'll be more careful next time Again thanks.

  7. #6
    Wiihacks Recommended
    Pro Installer/Store
    Senior Member
    Spyman's Avatar
    Join Date
    Jun 2008
    Location
    Greater Toronto Area
    Posts
    1,546
    Thanks
    33
    Thanked 123 Times in 106 Posts
    I always solder right to the pins :-p (usually) . Good practice for the upcoming epoxy. Anyways glad it worked out.
    Send me a PM if you need any Canadamods.ca support

    $9.95 Flat Rate Shipping to Canada & USA
    Official Support for Canadamods. I am here to help.

    email: sales@canadamods.ca | website: http://www.canadamods.ca | Phone: +1 416 728 0648

    We are the Official Distributors for: P.3Key, Wode JukeBox, WasabiDX, WiiKey, DriveKey, M3i & More - Always Authentic Guarenteed !
    Buy Wode JukeBox v2.0 here: Here

  8. #7
    New Member §piktsµ's Avatar
    Join Date
    May 2008
    Location
    Orlando, FL - USA
    Posts
    548
    Thanks
    6
    Thanked 24 Times in 22 Posts
    Awesome brother have fun...

  9. #8
    Junior Member
    Join Date
    Aug 2008
    Posts
    33
    Thanks
    3
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by Spyman View Post
    I always solder right to the pins :-p (usually) . Good practice for the upcoming epoxy. Anyways glad it worked out.
    I did a European D2E yesterday, no epoxy, very fresh stock I assume. It's from Spain's largest Retailer. How soon do you think it will be before the epoxy hits the european market and apart from the alternate solder points, is the only way to install, by removing the black stuff?

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •