Results 1 to 6 of 6

Thread: Wiikey 2 solderless Im freaking out

  1. #1
    Junior Member
    Join Date
    Mar 2009
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Wiikey 2 solderless Im freaking out

    Okay ive been waiting patiently for my wiikey 2 to come in from canada for 3 weeks, it comes in and i figured it would b a easy install, i look at my wii take it apart easily and properly install the solderless wiikey 2 and im lookin at it and its missing 3 connections, d,e,f, and i checked the serial and my wii is said to be Your Drive Chip is most likely GC2-D2B.

    Your Drive Pins are most likely not cut.

    I look at the chip and it says it a gc2-d1, ive done the wiikey with wires and it worked for most of the time, a few small problems but nothing major, I get this wiikey 2 and it doesnt work PLEASE HELP SOMEONE!!!

  2. #2
    Wiihacks Recommended
    Pro Installer/Store
    Senior Member
    Spyman's Avatar
    Join Date
    Jun 2008
    Location
    Greater Toronto Area
    Posts
    1,546
    Thanks
    33
    Thanked 123 Times in 106 Posts
    d,e,f arent supposed to be connected, and in your case if its a d2b then you need to disconnect G as its a legacy drive and won't work if its connected/wired for d2c and up. So cust the G trace.
    Send me a PM if you need any Canadamods.ca support

    $9.95 Flat Rate Shipping to Canada & USA
    Official Support for Canadamods. I am here to help.

    email: sales@canadamods.ca | website: http://www.canadamods.ca | Phone: +1 416 728 0648

    We are the Official Distributors for: P.3Key, Wode JukeBox, WasabiDX, WiiKey, DriveKey, M3i & More - Always Authentic Guarenteed !
    Buy Wode JukeBox v2.0 here: Here

  3. #3
    Junior Member
    Join Date
    Mar 2009
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Its not D2B ITS A D1 CHIPSET!!!!

  4. #4
    Wiihacks Recommended
    Pro Installer/Store
    Senior Member
    Spyman's Avatar
    Join Date
    Jun 2008
    Location
    Greater Toronto Area
    Posts
    1,546
    Thanks
    33
    Thanked 123 Times in 106 Posts
    you're looking at the wrong area , look at the chipset higher up, the smaller one...the one you clip onto... careful as well with the clip, continuously removing it and putting it on will ruin it. to remove it use a blade in the corner to pop it up.
    Send me a PM if you need any Canadamods.ca support

    $9.95 Flat Rate Shipping to Canada & USA
    Official Support for Canadamods. I am here to help.

    email: sales@canadamods.ca | website: http://www.canadamods.ca | Phone: +1 416 728 0648

    We are the Official Distributors for: P.3Key, Wode JukeBox, WasabiDX, WiiKey, DriveKey, M3i & More - Always Authentic Guarenteed !
    Buy Wode JukeBox v2.0 here: Here

  5. #5
    Junior Member
    Join Date
    Mar 2009
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    ahhh it is d2b! thanks so much, so can i just desolder all of the defg lines or should i cut it and if cut how do i do that

  6. #6
    Junior Member
    Join Date
    Mar 2009
    Posts
    15
    Thanks
    5
    Thanked 0 Times in 0 Posts
    NOT to highjack--but i have a d1a with same chip and same problem---are you saying to just unsolder g or to also cut the trace--thanks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •