Results 1 to 4 of 4

Thread: Guide: How To Install A WiiClip

  1. #1
    e39
    e39 is offline
    Member
    Join Date
    Dec 2008
    Posts
    1,029
    Thanks
    15
    Thanked 1,340 Times in 187 Posts

    Guide: How To Install A WiiClip

    Guide: How To Install A WiiClip
    by e39
    January 12, 2008


    Disclaimer:
    I am not liable for any damages incurred to your Wii console. The guide's user takes full responsibility for their actions.


    Please use your head.
    - If a screw isn't coming out, don't spin your screw driver into it until the head strips.
    - If you see cables, don't put anything sharp close to it.
    - Don't leave your console plugged into a wall outlet.
    - Don't leave your console attached to your TV.
    - Don't leave the sensor bar attached to the Wii.
    - Be organized with your screws. They're tiny. I have no idea where you can get more if you lose them.
    - Don't work on a carpeted surface. Static shock can travel and damage the components.


    Purpose:
    The purpose of this thread is to display the proper installation of a WiiClip onto the Wii console. Also, it is can be used as an addition to the disassemble guide.


    Tools:
    A set of clean hands


    The disassemble guide left you off at this point.

    As you can see, the WiiClip is ready for fitting. There are no drive chip pin obstructions and everything looks good.


    Fit the clip onto the drive chip.

    Use a small bit of pressure to make sure that the clip "pops" into place. No need for GI Joe kung-fu grip. No need for gorilla hands. Just press to make sure the clip has seated properly into place.


    Take another look around, make sure there's no severe gaps.



    Remember the goofy looking Super Mario Bros 3 card that came packed with the clip? It's functional.



    Remove the perforated section and fit the card over the clip.

    This will prevent electrical shorts. The card will shield against modchip metal to Wii internal metal contact.


    If you found this guide to be useful, please hit the in the corner. User feedback keeps me motivated!
    Last edited by e39; 01-12-2009 at 02:34 PM.

    Helpful Threads:
    Dump & Burn discs | 3.3 / 3.4 Firmware FYI | Wii Disassemble | WiiClip Install

    Consoles:
    Wii - 4.1U - WiiKey 2 - USBLoader GX - SNES9X GX, Genesis Plus GX, FCE GX w. cover flow mods
    360 - Resident Evil S.E. - iXtreme LT 1.1 - JTag - FreeBoot 0.032 9199 Dash - NXE2GOD, XM360, XeXMenu 1.1, Flash360
    PSP - CFW 5.00m33, 16GB MSPD | DS Lite - DSTT w.1.17a r12, 8GB SDHC


  2. #2
    Junior Member
    Join Date
    Dec 2008
    Posts
    4
    Thanks
    0
    Thanked 1 Time in 1 Post
    that chip u show to clip on to is not in my wii

  3. 1 User Says Thank You greevio For This Useful Post


  4. #3
    Junior Member
    Join Date
    Aug 2009
    Posts
    1
    Thanks
    1
    Thanked 1 Time in 1 Post
    many thanks...........well presented.

  5. 1 User Says Thank You liamreynolds For This Useful Post


  6. #4
    Junior Member
    Join Date
    Nov 2009
    Posts
    2
    Thanks
    1
    Thanked 1 Time in 1 Post
    dank u: thats dutch for thanks!!!

  7. 1 User Says Thank You jeepke For This Useful Post


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •