Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 21

Thread: D2B Wii + Wasabi v3 & clip ??

  1. #11
    Wiihacks Recommended
    Pro Installer/Store
    Senior Member
    Spyman's Avatar
    Join Date
    Jun 2008
    Location
    Greater Toronto Area
    Posts
    1,546
    Thanks
    33
    Thanked 123 Times in 106 Posts
    I would not recommend speaker wire, but if you have any other wire it could do. Speakerwire has magnetic properties to it, though it may be minimal to not do anything it still wouldnt be the recommended type. if youre using uninsulated wire, make sure you put tape or something around it so that it doesnt short anything.
    Send me a PM if you need any Canadamods.ca support

    $9.95 Flat Rate Shipping to Canada & USA
    Official Support for Canadamods. I am here to help.

    email: sales@canadamods.ca | website: http://www.canadamods.ca | Phone: +1 416 728 0648

    We are the Official Distributors for: P.3Key, Wode JukeBox, WasabiDX, WiiKey, DriveKey, M3i & More - Always Authentic Guarenteed !
    Buy Wode JukeBox v2.0 here: Here

  2. #12
    Junior Member
    Join Date
    Sep 2008
    Posts
    10
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by Spyman View Post
    if you ordered the d2b specific version though it should all be done for you except F point which they specify you need to solder.
    well it turned out that the soldering option for $5 was just to solder the chip to the clip, they didn't do anything else for it. I wish I would have gone with one of ya'll instead of trying to save a few bucks. But what can I say, this has definitely been a learning experience for me.

  3. #13
    Junior Member
    Join Date
    Sep 2008
    Posts
    10
    Thanks
    0
    Thanked 0 Times in 0 Posts
    its the only wire that i just happen to have laying around the house. if you couldn't tell from the rest of the thread, i am pretty much new to all of this stuff. You gotta learn somehwere, right?

  4. #14
    Junior Member
    Join Date
    Sep 2008
    Posts
    10
    Thanks
    0
    Thanked 0 Times in 0 Posts
    i am going to go by my local hardware shop tomorrow and see if they have anything else that would be more suitable (and hopefully not in a huge spool). Is there a certain type of wire I should look for?

  5. #15
    Junior Member
    Join Date
    Sep 2008
    Posts
    10
    Thanks
    0
    Thanked 0 Times in 0 Posts
    i found the wire. I thought I would dig through the vacuum bin again and there it was

  6. #16
    Junior Member
    Join Date
    Sep 2008
    Posts
    10
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by GMODZ View Post
    yes you can cut it with scissors as well....shorting D2B jumper means connecting the 2 golden pads. you can see the jumper one shorted on the pic below
    do you cut through the entire clip where those lines are or just through the top surface where you can see the lines?

  7. #17
    Member Dark Mod's Avatar
    Join Date
    Sep 2008
    Location
    Trinidad W.I
    Posts
    686
    Thanks
    0
    Thanked 11 Times in 10 Posts
    I think just the four traces alone.
    Thanks everyone for the great support.
    Hope to hear from you soon, cause i'm getting ready to retire from the modding scene.
    Gonna start a new profession.

  8. #18
    Junior Member
    Join Date
    Oct 2008
    Posts
    4
    Thanks
    0
    Thanked 0 Times in 0 Posts
    i have a DMS drive, i did everything (but short the c-d and the f wire came already soldered to the Q on the wii-clip (apparently so i don't have to solder to my wii)) so my question is: how do i short the C and D when everything is already soldered onto the clip
    Last edited by Hyper21; 10-12-2008 at 08:54 AM.

  9. #19
    Junior Member
    Join Date
    Oct 2008
    Posts
    4
    Thanks
    0
    Thanked 1 Time in 1 Post
    Same prob here!

    I ordered a pre soldered wasabi & wii clip. I thought my wii was d2c but it's d2b!

    So the clip is soldered for d2c with the F soldered to Q (I wasn't expecting this). Do I still need to solder F to the board on the wii?

    I can't even see the jumpers that I need to short on the wasabi!

    If anyone can help I'd really appreciate it as at the moment, i've bought a really expensive bookmark!

    thanks peeps!

    Sy

  10. #20
    Wiihacks Recommended
    Pro Installer/Store
    Senior Member
    Spyman's Avatar
    Join Date
    Jun 2008
    Location
    Greater Toronto Area
    Posts
    1,546
    Thanks
    33
    Thanked 123 Times in 106 Posts
    I helped hyper in another thread might want to look that one up.
    But you do not need to solder the F to the board on the wii, leave it as F to Q.

    You will need to short the jumper on the clip that says d2b, its in the middle of the point that says DMS, and the circular ring F .

    Then you will need to cut where it shows to cut it over here
    http://www.wii-clip.com/images/Wasabi_V5-14.jpg

    Again, you wont need to link F since its on a v5b and connected to Q.
    Send me a PM if you need any Canadamods.ca support

    $9.95 Flat Rate Shipping to Canada & USA
    Official Support for Canadamods. I am here to help.

    email: sales@canadamods.ca | website: http://www.canadamods.ca | Phone: +1 416 728 0648

    We are the Official Distributors for: P.3Key, Wode JukeBox, WasabiDX, WiiKey, DriveKey, M3i & More - Always Authentic Guarenteed !
    Buy Wode JukeBox v2.0 here: Here

Page 2 of 3 FirstFirst 123 LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •