Page 1 of 3 123 LastLast
Results 1 to 10 of 29

Thread: Does V4C-9 wii clip work on D2B chipset drives ?

  1. #1
    Junior Member tank's Avatar
    Join Date
    May 2008
    Location
    Ireland
    Posts
    27
    Thanks
    1
    Thanked 1 Time in 1 Post

    Does V4C-9 wii clip work on D2B chipset drives ?

    That is my question. I bought the v4c-9 clips thinking i could use my d2pro chips on all model chipset drives.
    It seems its just geared for the D2C chipset. Although the chips are Dms/D2A D2B and D2C compatible.

    I installed the clips. I get a constant error red light. The drive motor does not work. The system seems to start up ok (albeit no drive working).

    Have i simply purchased the wrong clips or is there jumpers/tracks that need to be broken/crossed ??

    Any help appreciated.....

    Thx
    Tank
    Last edited by tank; 06-20-2008 at 01:29 AM.

  2. #2
    Wiihacks Recommended
    Pro Installer/Store
    Senior Member
    Spyman's Avatar
    Join Date
    Jun 2008
    Location
    Greater Toronto Area
    Posts
    1,546
    Thanks
    33
    Thanked 123 Times in 106 Posts
    they can work, just have to modify it a bit check pm
    Send me a PM if you need any Canadamods.ca support

    $9.95 Flat Rate Shipping to Canada & USA
    Official Support for Canadamods. I am here to help.

    email: sales@canadamods.ca | website: http://www.canadamods.ca | Phone: +1 416 728 0648

    We are the Official Distributors for: P.3Key, Wode JukeBox, WasabiDX, WiiKey, DriveKey, M3i & More - Always Authentic Guarenteed !
    Buy Wode JukeBox v2.0 here: Here

  3. #3
    Junior Member
    Join Date
    Jun 2008
    Posts
    5
    Thanks
    0
    Thanked 0 Times in 0 Posts
    I also bought the wii-clip 4c and a d2pro v2 chip.

    I have not tried to install it yet, I am a little confused on what to solder, and if its going to work for the D2B chip.

    Do I solder all the points from the d2pro to the wii clip or just some of the points?

    The previous reply mentions that it has to be modded a little, does it and what is the mod?

  4. #4
    Junior Member
    Join Date
    Jun 2008
    Posts
    9
    Thanks
    0
    Thanked 0 Times in 0 Posts
    I have a Wii from launch day, so I assume I also have the D2B. I am also getting a D2Pro and a Wiiclip pre-soldered. Can you send me that pm on what I'll have to do to install properly and effectively?

  5. #5
    Wiihacks Recommended
    Pro Installer/Store
    Senior Member
    Spyman's Avatar
    Join Date
    Jun 2008
    Location
    Greater Toronto Area
    Posts
    1,546
    Thanks
    33
    Thanked 123 Times in 106 Posts
    Quote Originally Posted by spillb View Post
    I also bought the wii-clip 4c and a d2pro v2 chip.

    I have not tried to install it yet, I am a little confused on what to solder, and if its going to work for the D2B chip.

    Do I solder all the points from the d2pro to the wii clip or just some of the points?

    The previous reply mentions that it has to be modded a little, does it and what is the mod?
    check pm

    Quote Originally Posted by Twilightk View Post
    I have a Wii from launch day, so I assume I also have the D2B. I am also getting a D2Pro and a Wiiclip pre-soldered. Can you send me that pm on what I'll have to do to install properly and effectively?
    if youre getting it presoldered from us and buying the one for dms/d2a/d2b then you wont need to do anything, just install it and youre good to go.

    Al
    Send me a PM if you need any Canadamods.ca support

    $9.95 Flat Rate Shipping to Canada & USA
    Official Support for Canadamods. I am here to help.

    email: sales@canadamods.ca | website: http://www.canadamods.ca | Phone: +1 416 728 0648

    We are the Official Distributors for: P.3Key, Wode JukeBox, WasabiDX, WiiKey, DriveKey, M3i & More - Always Authentic Guarenteed !
    Buy Wode JukeBox v2.0 here: Here

  6. #6
    Junior Member
    Join Date
    Jun 2008
    Posts
    7
    Thanks
    1
    Thanked 0 Times in 0 Posts
    Can I have that PM too, I know d2pro9 v2 works with all board. What wii-clip should I use if I want to install d2pro9v2 on a d2b? d2a? dma? dc2? d2c2? Any help will do thanks

  7. #7
    Junior Member
    Join Date
    Jun 2008
    Posts
    9
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Awesome, thanks Spyman!

  8. #8
    Junior Member
    Join Date
    Jul 2008
    Posts
    2
    Thanks
    1
    Thanked 0 Times in 0 Posts
    I need that information too, please! I am having a lot of problems with this d2pro9 in a d2b chipset, it works sometimes, but now it doesnt work, it turns red light, blue light, red and blue at random times every time I turn the wii on.
    Please and thanks.

    Oh I forgot to say that Im using it with a wii-clip.

  9. #9
    Junior Member
    Join Date
    Jul 2008
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hi I was wondering if I could get that pm as well? I got the d2pro9 with the wii-clip v4 and want to install it on d2a.

    Thanks!

  10. #10
    Junior Member
    Join Date
    Jul 2008
    Posts
    2
    Thanks
    1
    Thanked 0 Times in 0 Posts
    please people, I really need that info so I can get this working.

    PS. I dont understand why with privmsg if this is a forum, we are supposed to see other peoples issues so we can fix our problems without bothering someone.

Page 1 of 3 123 LastLast

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •