|SNEEK+DI| OR |UNEEK+DI|
ONLY WORKS ON 4.2 EMULATED NAND
You will Need: [SPOILER="Getting a NAND backup for SNEEK+DI or UNEEK+DI"]Creating a NAND backup for SNEEK or UNEEK
Bootmii...as boot2 or iOS...
SD card..Best results are with non-SDHC cards..formatted to FAT32
Before you can use SNEEK/UNEEK you will need a NAND Backup.Two ways of getting it:
1.Use Bootmii and do a Nand Back Up ....then use Showmiiwads to extract the nand(shown below)
2.Use the FSDumper...rename the .dol to boot.dol put it in apps folder on your SD and launch via homebrew channel make sure you have 600 mb free on sd....(Takes 20min+)
1.Move the NAND back up from the SD(if you just made it) to your Computer..
2.Start ShowMiiWads Allow Internet Access...Go to Tools and select create COMMON-KEY it will tell you so type "45e"
3.Then Under Tools select Extract BootMii Dump.
4.Find where your bootmii dump is and select nand.bin
5.Let the program do its work . Once its done a new folder called nand-extracteda will be at the same directory as the nand.bin. Copy all Folders inside this folder to the SD card root or USB root for UNEEK..
They should be:
If you used the FSDumper you would get the same folders.[/SPOILER][SPOILER="|Creating a 4.2 Nand With Showmiiwads|"]|Creating a 4.2 Nand With Showmiiwads|
1. Download iOS [70v6678] for the SM 4.2 with NUSD, make sure you decrypt it and pack a .wad
2. Download System Menu 4.2 NUSD, decrypt it and pack a .wad
Also download these ios 9,12,15,17,21,22,28,33,34,35,36,37,38,53,55,56,(57 ,58)
3. Create a New folder on desktop (name it "New NAND")
4. Open ShowMiiWads
5. Click on Options -> Change NAND backup path. Select the folder you just created.
6. Click on View -> ShowMiiWads open the folder where SM.wad and your SM iOS.wad are.When they load up right click and select extract to Nand.In the folder you created you will have these folders
9. Copy your setting.txt & iplsave.bin from an actual dump to the /title/00000001/00000002/data folder that was created in your new folder.
10.Copy your cert.sys & uid.sys from an actual dump to /sys/
11. Copy the four folders: title,ticket,sys,shared1 to the root of whatever device you are going to be using to host your NAND.
11. Launch SNEEK/UNEEK and it will be as if it is the first time you started your wii
WILL give you a black screen for couple of minutes before it goes to first time set up.
WILL give you a black screen for couple of minutes between the health screen and showing you the system menu.
This is for the first time only. After that it should load fast.
or you can use NUSAD(better all in one go)[/SPOILER][SPOILER="|Installing SNEEK+ DI|OR |UNEEK+DI|"]|Installing SNEEK+ DI|OR |UNEEK+DI|
Sneek Installer 0.1b5
1.Extract the SneekInstaller.rar...open the .exe
2.In top right corner chose SNEEK+DI or UNEEK+DI
3.Browse For SNEEK Files select the folder you want then click on Get Files do the same for IOS Files
4.Then select your SD.If you Chose SNEEK+DI you will have these files on SD
If you Chose UNEEK+DI you will have this files on SD & USB
/sneek/kernel.bin[/SPOILER][SPOILER="|FILE STRUCTURE|"]|FILE STRUCTURE|:
[/SPOILER][SPOILER="|Wii Game File and Folder Structure|:"]|Wii Game File and Folder Structure|:
Example:usb:\games\your game\extracted files
- slot.bin( it is a file that is automatically generated by SNEEK when games are detected in the USB drive)
|THE HDD/FlashDrive NEEDS TO BE FAT32(32KB Clusters) & Set to PRIMARY|
[/SPOILER][SPOILER="|Tools to acquire game structure used by SNEEK's DI module|"]|Tools to acquire game structure used by SNEEK's DI module|
Open up WiiJManager and choose the drive/folder where your games are located.
It will then identify the game/games
Then right click the game and choose "convert to SNEEK"
When done converting rename the folder to what you like and place it on your drive.
DiscEX extracts the files of a game partition from
a Wii disc into the structure used by SNEEK's DI module.
[/SPOILER][SPOILER="|Accessing SNEEK+DI Menu|"]|Accessing SNEEK+DI Menu|
GameCube Controller in port 1 or Wiimote
Wii Remote -> Press "1" -> select game -> press A -> press start ->Game will load now in DC
GC->Press Start -> Select Game -> Press A -> Press Start the game will load now in DC
You need to have font.bin located in the root of the SD card or USB(for UNEEK)
A GC controller needs to be plugged into the 1st port.
Once the system menu has loaded:
Press START on the GC controller to access the game selection menu.
Use the D-PAD to scroll through the games and press A to select the game.
Press start again to return to the system menu.
If everything is working, whatever game is currently in the disc channel will disappear:
You'll see the eject disc animation.
The disc channel will then appear empty.
Click on the disc channel,
It will then load up the banner for whatever game you chose.
Gamecube controller has to be plugged before booting the Wii.
Connecting it once the system menu is showing doesn't work.
[/SPOILER][SPOILER="Usefull Downloads:"]Usefull Downloads:
Multi-Mod Manager(Great app that does it all)
Easeus Partition Manager(To Format your HDD)[/SPOILER][SPOILER="Error"]Error:
1 short flash : The TMD of the requested title is missing
2 short flashes: The TMD of the IOS the current title uses is missing
3 short flashes: The kernel.bin is not found on sd and or usb
4 short flashes: Failed to load the requested IOS (missing IOS, missing TMD/Ticket/content)
5 short flashes: "Could not open or read sd:/sneek/kernel.bin[/SPOILER]
THANKS GOES TO