Search:

Type: Posts; User: allsystemsgo

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Wiikey2 salvaged from a NTSC system. Want to use it in a PAL system now, but ..

    Let's see if the hardcore modders are still alive :)

    I need a Wiikey2 for 2 people.. and I have 2.. problem is that one of them is new (yay :)) and the other one is from an NTSC Wii with region...
  2. Replies
    22
    Views
    1,568

    I trust you checked here as well :...

    I trust you checked here as well : http://www.wiihacks.com/bricked-wii-issues-only/35569-nand-programming-low-level-brick-recovery-without-bootmii.html ?

    (of course, if your Wii doesn't have a...
  3. Sticky: This is the Infectus ground bounce. Well...

    This is the Infectus ground bounce. Well documented on how to prevent this, even in this very thread :)
    (use multiple ground wires..)
  4. Sticky: in that case, have you tried disconnect/connect...

    in that case, have you tried disconnect/connect in nand flasher a few times ? If that doesn't help, check the via's to check if the connections have been made properly (see this topic for a diagram)
  5. Sticky: You could edit the xml file and add an entry by...

    You could edit the xml file and add an entry by copying the correct identifier block (but using the identifier you're getting now) so you will be able to recognize the nand chip again. Write the...
  6. Sticky: So just flash the bootmii 8 blocks first and then...

    So just flash the bootmii 8 blocks first and then flash 0-152063 (dec) with the original one. I did something similar last night, but that didn't work. Will solder the infectus back on ;)
  7. Sticky: I've sent you the first 8 blocks of the NAND....

    I've sent you the first 8 blocks of the NAND. Hope you can see what it is. If the nand legs have a short or not connected properly, then shouldn't I see the same behavior when I flash back the...
  8. Sticky: Ok, new Wii, new situation :) Korean Wii. User...

    Ok, new Wii, new situation :)

    Korean Wii. User had it regionchanged to PAL and somehow managed to brick it by updating to 4.2USA. Serial LKM1007/ Hollywood 0814. So I figured I could use a bootmii...
  9. Sticky: dat mag ook wel es een keer na al die 1c's die ik...

    dat mag ook wel es een keer na al die 1c's die ik niet kon fixen..
  10. Sticky: Are you sure you want to do this ? From the...

    Are you sure you want to do this ? From the sounds of it, you might be better off practicing a bit on old mainboard/videocards before you venture into this project.

    Anyway, I tin the wire, dip it...
  11. Sticky: Whichever is more comfortable to you. I solder...

    Whichever is more comfortable to you. I solder them over the lenght of the leg (straight up) so you have a strong bond. You can also use the part of the leg that's flat on the board. Like I said,...
  12. Sticky: Fixed !

    The Wii I was talking about a page earlier is fixed. Had to rewrite the original 8 blocks (with the theme brick) back first since it still had 8 blocks from a boot1b bootmii dump after my last...
  13. Sticky: Ok, will try tonight. I already tried the various...

    Ok, will try tonight. I already tried the various recovery discs out there and they don't load at all, since HBC iso did work I figured I had to make one myself :)
  14. Sticky: Formatter

    Just wondering. I have a bricked Wii here which has 1c and no way of fixing it due to not having the keys.

    However, it does 'work' with SaveMii(Frii). 4.2EUR and it also starts autoboot discs that...
  15. Sticky: Any thicker and I could have used electrical wire...

    Any thicker and I could have used electrical wire (the kind you use in your house to wire your outlets :)) :D
  16. Sticky: and that's why you wrote the tut and I just...

    and that's why you wrote the tut and I just follow it :D
  17. Sticky: Thank you :)

    Just a quick post to once again thank erikie. I've done a few Wii's with his guide so far, but unfortunately all of them were boot1c.

    Until last night :) LEH144xx, 729.. on hollywood, D-2...
  18. Replies
    9
    Views
    1,234

    FBFB I have had a problem with (soldering wires...

    FBFB I have had a problem with (soldering wires to the nand) was caused by connect 2 having a bad contact. Resoldered that and problem solved.

    Also, did you try to disconnect/connect a couple of...
  19. Replies
    14
    Views
    4,914

    Anyone heard of this ?

    Just got this offer from my China contact :





    Never mind, it's some kind of homebrew/softmod contraption :
  20. My friend erikie found it again :

    My friend erikie found it again :
  21. There was an interview once with Team...

    There was an interview once with Team Twiizers/Bushing and in that interview he/they talked about how they hooked up a terminal on the 4th gc port. Can't find the interview anywhere and I might be...
  22. Serial communication through gamecube controller port #4 as used by Bushing ?

    Bushing has supposedly used the fourth gamecube controller port to capture data via serial communication some time ago.

    Does anybody have a howto for this ? I'm curious to what goes over the line...
  23. Sticky: Instead of editing the above post.. It worked...

    Instead of editing the above post..

    It worked ! :)

    What did I do to make it work finally :

    - use 4 ground wires
    - long q wire (3-4 times longer than the other wires)
    - use D0-GND switch...
  24. Sticky: Using : Betwiin 1.0 Win32OpenSSL-0_9_8l...

    Using :

    Betwiin 1.0
    Win32OpenSSL-0_9_8l
    ActivePython 2.6.4.10
    Numpy 1.3
    Pycrypto 2.1

    I'll try today on an Ubuntu machine, maybe that will work better :)
  25. Sticky: Please see here :...

    Please see here : http://www.wiihacks.com/wii-custom-software-hacks-applications/21328-betwiin-10-beta-bushing-others.html

    No luck creating a new nand.bin I can use.

    Yes, I stripped the keys...
Results 1 to 25 of 37
Page 1 of 2 1 2