12-24-2010, 05:51 AM
Retired WiiHacks Staff
ok 1st you posted in the wrong section
Originally Posted by Rupert2010
2nd press power hold reset priiloader will start up go to system hacks enable block disc updates enable block online updates save (if you have priiloader installed)
thanks to bmarlo for this signature
12-24-2010, 06:59 AM
I have a hardmodded wii with a Firmware fo 4.3u. It is my sister's wii. I do not know what chip was used in it. It has trouble with certain games like New Super Mario Bros. I would like to get the USB HDD to work. I looked at the beginning of the guide and notice a section for hardmodded wii's and a section that is for 4.3u.
I guess since I am 4.3u I need to use SSBB or Lego Indiana jones even though the wii is hardmodded. Is this correct? Just want to make sure before I start. I see in SSBB I need to make a save. Can I use a NTSC iso to make this save. Does it ahve to be a original disc or is a backup fine?
12-24-2010, 09:46 AM
12-24-2010, 10:26 AM
Need help with overwrite.
Greetings and Happy Holidays WiiHacks community. I need a little help with system config and have been unable to find an answer searching the forum. I've followed Mauifrogs guide to update my softmodded wii (4.2u) (many kudos to Mauifrog btw, amazing package) and cannot overwrite a cIOS. I'm trying to install 249(56) and have 249(57) installed. The (56) wad installs without errors but WiiFlow still shows 249(57) after install. On the WiiFlow wiki it recommends 249(56) v20b with the new WiiFlow v2.2 and FAT32 drive. I am just curious why (56) won't overwrite (57)... Is it because the (57) rev is maxed out? Any help would be appreciated, I'd like to get to the bottom of this!
(Thanks in advance for those who decide to help, this is my first post and I hope I'm not bashed for it.)
12-24-2010, 11:22 AM
I am trying to mod my friend's brand new, virgin red wii (4.3).
I have SSMB, I keep the sd cart out, delete the stages, exit back out, pop in the sd card with the linked hack me files on it (extracted), go back into the stage editor.... NOTHING happens... what is going on?
12-24-2010, 11:39 AM
12-24-2010, 11:54 AM
Followed and hacked a black 4.3u. Right now trying some games, running smoothly.
However, I found one abnormality when installing priiloader. It showed two Warning messages about two .ini cannot replaced, but at the end it showed operation OK. This is the second Wii I've hacked with this guide, the first was 4.2u, but honestly speaking I cannot remember if I saw those warning messages.
Please let me know if those warnings are normal.
12-24-2010, 12:52 PM
I used the same guide as you have to allow my Wii HDD to load up.
Originally Posted by fullquiver
Once done I was left with the question "What to do next" and realized since the Wii boots the way it does via the SD card and the guide we both followed allows the hard drive to be used instead,I just used the files/folders from Mauifrogs guide "Chapter 3- The Final Step" since that is the guide I used to soft mod two Wii's successfully using a 8GB usb flash drive and SD card.
So far day three this is working well and no SD card incerted.
Last edited by noprob; 12-24-2010 at 12:55 PM.
12-24-2010, 12:56 PM
Originally Posted by Clivey
I'm also in the UK and have just bought this game. I didn't spend very long looking for it (couple of hours at most).
I got mine off of Playtrade (Play.com) for £47. in fact there is one on there right now for £54.95 (free delivery), Here,
so i'm not sure why your having so much trouble.
If you don't want to pay that much then rent it @ lovefilm or blockbuster.
12-24-2010, 01:21 PM
I figured it out, I didn't realize you have to move the extracted files to the root of the sd, I had them in that file that pops out after unzipping the rar
Originally Posted by peire
Tags for this Thread