Page 2 of 2 FirstFirst 12
Results 11 to 13 of 13

Thread: neek2o, Enhanced Uneek Setup

  1. #11
    New Member Brownbailey's Avatar
    Join Date
    Dec 2011
    Posts
    9
    Thanks
    2
    Thanked 0 Times in 0 Posts
    Currently I'm using an 8GB USB stick freshly formatted to FAT32, so there is only the one partition. I thought that might have been my problem originally with the 1TB, but now?

    Should I be not be renaming the kernel.bin to boot2_usb.bin since my Boot2 is IOS?
    Oops, I mean my Bootmii is ios...
    Last edited by Brownbailey; 12-15-2011 at 03:05 PM.

  2. #12
    New Member
    Join Date
    Dec 2011
    Posts
    49
    Thanks
    13
    Thanked 1 Time in 1 Post
    I've currently got Priloader autobooting to USB GX loader (all from USB HDD, no SD). I want to use Sneek to run one game and so I'm looking for a way to make it easy to swap between Sneek and USB GX Loader and was advised to use neek2o. However, my USB HD has a NTFS partition (it's in my media player and holds my video/audio files) followed by a FAT32 partition, which works fine with USB GX Loader, but from what I've read neek20 requires the FAT32 partition to be first, so I don't think I can use it.

    Is there any other way or will I just have to put the SD card in when I want to use Sneek and remove it when I want to use USB GX loader?

    EDIT: Hmm, apparently Sneek doesn't support loading games from SD and the limitation of requiring the FAT32 partition to be the first on the drive applies to Sneek, not just neek20, so looks like I'm stuffed!
    Last edited by doveman; 03-22-2012 at 08:40 AM.

  3. #13
    New Member
    Join Date
    Dec 2011
    Posts
    49
    Thanks
    13
    Thanked 1 Time in 1 Post
    I thought I'd have a play around anyway. I thought with the SD card in it would straight boot to neek on that, but it still boots to USBLoaderGX on my USB HDD. I'm afraid I can recall the name of the tool I used to build Neek+DI/Uneek+DI but it was a text-based window which asked me a few questions before downloading some files and generated a folder to copy to my SD card.

    If I try and install the neek2o_NK2O_1.wad WAD with MMM, I get "Ticket (-2011). 1 did not complete"

    If I boot the Wii normally to USBLoaderGX, then go to Homebrew and select Postloader or PribooterGUI it loads Postloader.

    If I run the neekbooter.dol from MMM from my SNEEK+DI or UNEEK+DI SD card (I'm using two SD cards) it loads Postloader and then I select Priibootergui and that says it's booting in Real NAND mode and to press a button to change this, so I press a button and select Neek2o and I just get a black screen and have to hold the power button to turn off the Wii.

    If in Postloader I go to Browse - Game Mode, it shows me the games on my USB HDD and I can load them (after I set the default loader to USBLoaderGX).

    I had a lot of problems with the controllers loosing sync as well, and luckily found that by booting to Priloader by holding Reset when powering on, then holding Eject and pressing reset it would boot to the normal dash, or at least the screen where it says Press A, and from there the Sync button on the Wii worked.

    EDIT: OK, got home and checked and it was ModMii6.0.6 I used to build and I built Sneek2o and Sneek2o+DI (not UNEEK+DI). As I say, neither of them were working though.
    Last edited by doveman; 04-01-2012 at 04:52 PM.

Page 2 of 2 FirstFirst 12

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •