Results 1 to 2 of 2

Thread: Network / Router / Switch / Modem Glossary

  1. #1
    Admin / Super Mod ModderMan's Avatar
    Join Date
    Nov 2006
    Location
    GVR
    Posts
    8,841
    Thanks
    758
    Thanked 1,418 Times in 328 Posts
    Blog Entries
    15

    Network / Router / Switch / Modem Glossary



    Access Point

    Access points are way stations in a wireless LAN that are connected
    to an Ethernet hub or server. Users can roam within the range of
    access points and their wireless device connections are passed from
    one access point to the next.


    Authentication
    Authentication refers to the verification of a transmitted message's integrity.


    DMZ
    DMZ (DeMilitarized Zone) is a part of an network that is located
    between a secure LAN and an insecure WAN. DMZs provide a way for some
    clients to have unrestricted access to the Internet.


    Beacon Interval
    Refers to the interval between packets sent sent by access points for
    the purposes of synchronizing wireless LANs.


    DHCP
    DHCP (Dynamic Host Configuration Protocol) software automatically
    assigns IP addresses to client stations logging onto a TCP/IP
    network, which eliminates the need to manually assign permanent IP addresses.


    DNS
    DNS stands for Domain Name System. DNS converts machine names to the
    IP addresses that all machines on the net have. It translates from
    name to address and from address to name.


    Domain Name
    The domain name typically refers to an Internet site address.


    DTIM
    DTIM (Delivery Traffic Indication Message) provides client stations
    with information on the next opportunity to monitor for broadcast or
    multicast messages.


    Filter
    Filters are schemes which only allow specified data to be
    transmitted. For example, the router can filter specific IP addresses
    so that users cannot connect to those addresses.


    Firewall
    Firewalls are methods used to keep networks secure from malicious
    intruders and unauthorized access. Firewalls use filters to prevent
    unwanted packets from being transmitted. Firewalls are typically used
    to provide secure access to the Internet while keeping an
    organization's public Web server separate from the internal LAN.


    Firmware
    Firmware refers to memory chips that retain their content without
    electrical power (for example, BIOS ROM). The router firmware stores
    settings made in the interface.


    Fragmentation
    Refers to the breaking up of data packets during transmission.


    FTP
    FTP (File Transfer Protocol) is used to transfer files over a TCP/IP
    network, and is typically used for transferring large files or
    uploading the HTML pages for a Web site to the Web server.


    Gateway
    Gateways are computers that convert protocols enabling different
    networks, applications, and operating systems to exchange information.


    Host Name
    The name given to a computer or client station that acts as a source
    for information on the network.


    HTTP
    HTTP (HyperText Transport Protocol) is the communications protocol
    used to connect to servers on the World Wide Web. HTTP establishes a
    connection with a Web server and transmits HTML pages to client
    browser (for example Windows IE). HTTP addresses all begin with the
    prefix 'http://' prefix (for example, Yahoo!).


    ICMP
    ICMP (Internet Control Message Protocol) is a TCP/IP protocol used to
    send error and control messages over the LAN (for example, it is used
    by the router to notify a message sender that the destination node is
    not available).


    IP
    IP (Internet Protocol) is the protocol in the TCP/IP communications
    protocol suite that contains a network address and allows messages to
    be routed to a different network or subnet. However, IP does not
    ensure delivery of a complete message—TCP provides the function
    of ensuring delivery.



    IP Address
    The IP (Internet Protocol) address refers to the address of a
    computer attached to a TCP/IP network. Every client and server
    station must have a unique IP address. Clients are assigned either a
    permanent address or have one dynamically assigned to them via DHCP.
    IP addresses are written as four sets of numbers separated by periods
    (for example, 211.23.181.189).


    ISP
    An ISP is an organization providing Internet access service via
    modems, ISDN (Integrated Services Digital Network), and private lines.


    LAN
    LANs (Local Area Networks) are networks that serve users within
    specific geographical areas, such as in a company building. LANs are
    comprised of servers, workstations, a network operating system, and
    communications links such as the router.



    MAC Address
    A MAC address is a unique serial number burned into hardware
    adapters, giving the adapter a unique identification.


    Metric
    A number that indicates how long a packet takes to get to its destination.


    MTU
    MTU (Maximum Transmission/Transfer Unit) is the largest packet size
    that can be sent over a network. Messages larger than the MTU are
    divided into smaller packets.



    NAT
    NAT (Network Address Translation - also known as IP masquerading)
    enables an organization to present itself to the Internet with one
    address. NAT converts the address of each LAN node into one IP
    address for the Internet (and vice versa). NAT also provides a
    certain amount of security by acting as a firewall by keeping
    individual IP addresses hidden from the WAN.


    (Network) Administrator
    The network administrator is the person who manages the LAN within an
    organization. The administrator's job includes ensuring network
    security, keeping software, hardware, and firmware up-to-date, and
    keeping track of network activity.


    NTP
    NTP (Network Time Protocol) is used to synchronize the realtime clock
    in a computer. Internet primary and secondary servers synchronize to
    Coordinated Universal Time (UTC).



    Packet
    A packet is a portion of data that is transmitted in network
    communications. Packets are also sometimes called frames and
    datagrams. Packets contain not only data, but also the destination IP address.


    Ping
    Ping (Packet INternet Groper) is a utility used to find out if a
    particular IP address is present online, and is usually used by
    networks for debugging.


    Port
    Ports are the communications pathways in and out of computers and
    network devices (routers and switches). Most PCs have serial and
    parallel ports, which are external sockets for connecting devices
    such as printers, modems, and mice. All network adapters use ports to
    connect to the LAN. Ports are typically numbered.



    PPPoE
    PPPoE (Point-to-Point Protocol Over Ethernet) is used for running PPP
    protocol (normally used for dial-up Internet connections) over an Ethernet.


    Preamble
    Preamble refers to the length of a CRC (Cyclic Redundancy Check)
    block that monitors communications between roaming wireless enabled
    devices and access points.


    Protocol
    A protocol is a rule that governs the communication of data.



    RIP
    RIP (Routing Information Protocol) is a routing protocol that is
    integrated in the TCP/IP protocol. RIP finds a route that is based on
    the smallest number of hops between the source of a packet and its destination.


    RTS
    RTS (Request To Send) is a signal sent from the transmitting station
    to the receiving station requesting permission to transmit data.


    Server
    Servers are typically powerful and fast machines that store programs
    and data. The programs and data are shared by client machines
    (workstations) on the network.



    SMTP
    SMTP (Simple Mail Transfer Protocol) is the standard Internet e-mail
    protocol. SMTP is a TCP/IP protocol defining message format and
    includes a message transfer agent that stores and forwards mail.


    SNMP
    SNMP (Simple Network Management Protocol) is a widely used network
    monitoring and control protocol. SNMP hardware or software components
    transmit network device activity data to the workstation used to
    oversee the network.


    SSID
    SSID (Service Set Identifier) is a security measure used in WLANs.
    The SSID is a unique identifier attached to packets sent over WLANs.
    This identifier emulates a password when a wireless device attempts
    communication on the WLAN. Because an SSID distinguishes WLANS from
    each other, access points and wireless devices trying to connect to a
    WLAN must use the same SSID.



    Subnet Mask
    Subnet Masks (SUBNETwork masks) are used by IP protocol to direct
    messages into a specified network segment (i.e., subnet). A subnet
    mask is stored in the client machine, server or router and is
    compared with an incoming IP address to determine whether to accept
    or reject the packet.


    SysLog Server
    A SysLog server monitors incoming Syslog messages and decodes the
    messages for logging purposes.


    TCP
    (Transmission Control Protocol) is the transport protocol in TCP/IP
    that ensures messages over the network are transmitted accurately and completely.



    TCP/IP
    TCP/IP (Transmission Control Protocol/Internet Protocol) is the main
    Internet communications protocol. The TCP part ensures that data is
    completely sent and received at the other end. Another part of the
    TCP/IP protocol set is UDP, which is used to send data when accuracy
    and guaranteed packet delivery are not as important (for example, in
    realtime video and audio transmission).


    The IP component of TCP/IP provides data routability, meaning that
    data packets contain the destination station and network addresses,
    enabling TCP/IP messages to be sent to multiple networks within the
    LAN or in the WAN.


    Telnet
    Telnet is a terminal emulation protocol commonly used on the Internet
    and TCP- or IP-based networks.


    Telnet is used for connecting to remote devices and running programs.
    Telnet is an integral component of the TCP/IP communications protocol.



    UDP
    (User Datagram Protocol) is a protocol within TCP/IP that is used to
    transport information when accurate delivery isn't necessary (for
    example, realtime video and audio where packets can be dumped as
    there is no time for retransmitting the data).


    Virtual Servers
    Virtual servers are client servers (such as Web servers) that share
    resources with other virtual servers (i.e., it is not a dedicated server).


    WEP
    WEP (Wired Equivalent Privacy) was the de facto security protocol for
    wireless LANs, providing the "equivalent" security
    available in hardwired networks.
    Most 802.11 devices allow WEP keys to be entered using an ASCII passphrase or in hexidecimal format. The conversion between these two formats is an industry standard which is shared by almost all vendors of 802.11 equipment.

    WPA and WPA2
    is a certification program developed by the Wi-Fi Alliance to indicate compliance with the security protocol created by the Wi-Fi Alliance to secure wireless computer networks. The Alliance defined the protocol in response to several serious weaknesses researchers had found in the previous system, WEP (Wired Equivalent Privacy)
    WPA2 has replaced WPA; WPA2 implements the mandatory elements of 802.11i. In particular, it introduces a new AES-based algorithm, CCMP, which is considered fully secure

    Wireless LAN
    Wireless LANs (WLANs) are
    local area networks that use wireless communications for transmitting
    data. Transmissions are usually in the 2.4 GHz band. WLAN devices do
    not need to be lined up for communications like infrared devices.
    WLAN devices use access points which are connected to the wired LAN
    and provide connectivity to the LAN. The radio frequency of WLAN
    devices is strong enough to be transmitted through non-metal walls
    and objects, and can cover an area up to a thousand feet. Laptops and
    notebooks use wireless LAN PCMCIA cards while PCs use plug-in cards
    to access the WLAN.


    WLAN
    WLANs (Wireless LANs) are
    local area networks that use wireless communications for transmitting
    data. Transmissions are usually in the 2.4 GHz band. WLAN devices do
    not need to be lined up for communications like infrared devices.
    WLAN devices use access points which are connected to the wired LAN
    and provide connectivity to the LAN. The radio frequency of WLAN
    devices is strong enough to be transmitted through non-metal walls
    and objects, and can cover an area up to a thousand feet. Laptops and
    notebooks use wireless LAN PCMCIA cards while PCs use plug-in cards
    to access the WLAN.


    WAN


    WAN (Wide Area Network) is a communications network that covers a
    wide geographic area such as a country (contrasted with a LAN, which
    covers a small area such as a company building).
    Last edited by ModderMan; 05-10-2010 at 11:47 PM.

    Wiihacks Super Mod / Admin

  2. #2
    Junior Member
    Join Date
    May 2010
    Posts
    2
    Thanks
    0
    Thanked 0 Times in 0 Posts
    thanks for info, but as for me I like to use for monitoring bandwidth ProteMac meter

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •