Page 2 of 2 FirstFirst 12
Results 11 to 17 of 17

Thread: bootmii question

  1. #11
    New Member jerseywii's Avatar
    Join Date
    Jan 2009
    Location
    North Jersey
    Posts
    124
    Thanks
    14
    Thanked 16 Times in 14 Posts
    do the remotes turn the wii on and/or off?
    Give me a thanks if anything i said was useful or you found it remotely intuitive

    4.1U Softmodded and Cherished
    **cIOS38 rev17, Hermes v4, Priiloader 0.3b, Bootmii / boot2, USB Loader GX v849, 1TB Iomega Prestige Desktop Drive WBFS Formatted**

    3.4U Softmodded and Built From Parts
    3.2U Softmodded / Bricked

  2. #12
    New Member becksterorange's Avatar
    Join Date
    Dec 2009
    Location
    Arkansas
    Posts
    411
    Thanks
    28
    Thanked 55 Times in 49 Posts
    I know this sounds trivial, but when you re sync, just tap the button next to the sd card. Don't hold it. Then tap the button on the remote. Don't hold it. This is what worked for me when I was having trouble syncing my remote. It either only works that way, or I got lucky.
    Wii 4.1U - cIOS38 rev17 - 500gbHDD - Wiiflow 2.1 - uLoader 5.1 - Wimc 1.0.9 - Priiloader 0.5 - boot2 - gamecube launcher 2.0 - cMIOS rev3

  3. #13
    New Member
    Join Date
    Sep 2009
    Posts
    21
    Thanks
    4
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by jerseywii View Post
    do the remotes turn the wii on and/or off?
    Nope, The remotes just flash and then go off. I tried them on my other wii and they connect no problem.

  4. #14
    New Member becksterorange's Avatar
    Join Date
    Dec 2009
    Location
    Arkansas
    Posts
    411
    Thanks
    28
    Thanked 55 Times in 49 Posts
    Another thing you can look at, is to make sure your sensor bar is plugged securely into the back of your wii. I'm just grabbing at straws here.
    Wii 4.1U - cIOS38 rev17 - 500gbHDD - Wiiflow 2.1 - uLoader 5.1 - Wimc 1.0.9 - Priiloader 0.5 - boot2 - gamecube launcher 2.0 - cMIOS rev3

  5. #15
    New Member
    Join Date
    Sep 2009
    Posts
    21
    Thanks
    4
    Thanked 0 Times in 0 Posts
    I mean is this a syptom of a semi brick or a full brick? i have looked everywere too see if anyone has had this issue after soft modding but no one has said anything yet.

  6. #16
    Senior Member Cile's Avatar
    Join Date
    Nov 2009
    Location
    Australia
    Posts
    5,071
    Thanks
    666
    Thanked 2,302 Times in 1,226 Posts
    Blog Entries
    9
    Just cuz you didnt install bootmii it wouldnt have anythign do to with ur controlers not syncing

    I had a problem once they just ddint wanna sync so i just did wot it said on ninteno site and worked

    First, follow these guidelines to ensure you have set up the system properly to have the optimal environment in which to use the Wii Remote:

    * Check to make sure the Sensor Bar cord is inserted into the back of the Wii console and the Sensor Bar is centered above or below your TV screen (more info).
    * Make sure you are using fresh batteries in the Wii Remote.
    * The Wii Remote Controller should be used between 3 to 10 feet from the TV.
    * Make sure no objects are blocking the signals between the Sensor Bar, the Wii console, and the Wii Remote.
    * Check for interference from infra-red light sources, such as candles, sunlight, fireplaces, and stoves.
    * Radio frequency interference may cause the Wii Remote to work erratically. Check for wireless devices such as cordless phones, wireless computer keyboards or mice, or other similar devices, and move or turn them off.






    Try these steps!

    1. Turn the Wii console power OFF by pressing the POWER Button on the front of the console. Unplug the power cord from the wall outlet for a few seconds. After a few seconds have elapsed, plug the cord back into the wall outlet.

    2. Turn the power of the Wii console ON. When you see the Health and Safety screen, open the small flap on the front of the Wii console to find a red button labeled "SYNC." Press and hold the SYNC Button down for 15 seconds. This will clear all the syncs on the Wii, allowing you to get a clean start to begin the process described below.

    3. After holding the SYNC Button on the Wii console down for at least 15 seconds, you can now "re-sync" your Wii Remotes:

    1. With the first Wii Remote you wish to sync, remove the battery cover on the back of the Wii Remote to find a small red button just below the batteries.

    2. Press and release the small red button just below the batteries on the Wii Remote; the blue lights on the front of the Wii Remote will blink.

    3. Quickly press and release the red SYNC button on the inside of the white flap on the front of the Wii console (picture).

    4. When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).

    5. This sync procedure (steps "a" through "d" above) must be followed for each additional Wii Remote added to the system.

  7. #17
    Junior Member
    Join Date
    Dec 2009
    Posts
    2
    Thanks
    1
    Thanked 0 Times in 0 Posts
    Maybe the sensor wire
    Last edited by kevkalv; 02-11-2010 at 03:45 AM.

Page 2 of 2 FirstFirst 12

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •