Results 1 to 3 of 3

Thread: Questions on D2C2 D2Pro9 rev2.0 can't read disc error

  1. #1
    Junior Member
    Join Date
    Aug 2008
    Posts
    1
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Questions on D2C2 D2Pro9 rev2.0 can't read disc error

    Greetings, this is my first post here. Just wanted to drop a quick thanks for all the great info I've gotten so far, but still need some help.
    My Wii serial starts with LU5776, and it has the extra piece of metal on the DVD drive indicating most likely the D2C2 chipset.

    I bought the D2PRO9 rev 2.0 with WiiClip V4C from Canadamods. According to their site, the firmware on the chip is 1.3 updateable to 1.5. Installed the chip via WiiKey and can still read originals, but cannot get backups to read. The LED on the chip remains red at all times.

    I've burnt 5 backups on different media (sony -r and memorex -r) using ImgBurn...so I have a good number of test discs, none of which work. I'll burn more discs if I can get the chip LED to go off total red first and the games still don't work.


    Questions...

    1. I read about the J-wire CLK jumper mod sometimes needed to get some chips/keys working, when is this necessary? Do I need to do this?

    2. Can/Should I update the chip firmware from DVD when the LED is red or should I get it reading backup games successfully first?

    3. What is the maximum firmware I can update to? I can't find version 1.5 anywhere? Can I use the v1.6 utility disc from D2Pro9 resources site?

    4. Any other thoughts on getting this working properly?

    Thanks in advance.
    Cheers!

  2. #2
    Junior Member
    Join Date
    Jul 2008
    Posts
    4
    Thanks
    0
    Thanked 0 Times in 0 Posts
    is your chip and wiiclip solderless? If yes, press harder. At first time my always red, but i try to press harder the wii clip to the drive chip. It's green ( or bule) Good luck

  3. #3
    Wiihacks Recommended
    Pro Installer/Store
    Senior Member
    Spyman's Avatar
    Join Date
    Jun 2008
    Location
    Greater Toronto Area
    Posts
    1,546
    Thanks
    33
    Thanked 123 Times in 106 Posts
    Questions...

    1. I read about the J-wire CLK jumper mod sometimes needed to get some chips/keys working, when is this necessary? Do I need to do this?

    It may be necessary in this case, make sure none of the pins on the clip are bent first, most problems like this stem from an incorrect placement at first causing the pins to get bent. (check both the clip and the wii board)

    2. Can/Should I update the chip firmware from DVD when the LED is red or should I get it reading backup games successfully first?

    You can't without the programmer in this case if its not going into the normal stage.

    3. What is the maximum firmware I can update to? I can't find version 1.5 anywhere? Can I use the v1.6 utility disc from D2Pro9 resources site?

    You can use 1.6, we havent updated the description on our site to state that yet

    4. Any other thoughts on getting this working properly?

    Try the suggested, you can also send us the drive if you like and we can make sure everything is ok, solder the j point etc.
    Send me a PM if you need any Canadamods.ca support

    $9.95 Flat Rate Shipping to Canada & USA
    Official Support for Canadamods. I am here to help.

    email: sales@canadamods.ca | website: http://www.canadamods.ca | Phone: +1 416 728 0648

    We are the Official Distributors for: P.3Key, Wode JukeBox, WasabiDX, WiiKey, DriveKey, M3i & More - Always Authentic Guarenteed !
    Buy Wode JukeBox v2.0 here: Here

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •