Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: will the D2pro9 with clip work with my console

  1. #1
    New Member
    Join Date
    Aug 2008
    Posts
    40
    Thanks
    0
    Thanked 0 Times in 0 Posts

    will the D2pro9 with clip work with my console

    My wii serial number is LU32423228 the next number is 6 with a box around it. I wanted to know what is the best solderless modchip for my console to play backups

  2. #2
    Member
    Retired Staff Member

    Join Date
    Jun 2008
    Posts
    1,494
    Thanks
    70
    Thanked 230 Times in 116 Posts
    According to the Wii tracker -> Nintendo-Scene Wii Serial Tracker

    Your Drive Chip is most likely GC2-D2C.

    Your Drive Pins are most likely not cut.
    Yes, your console will work with D2Pro9

  3. #3
    Reading Room
    Join Date
    May 2008
    Posts
    414
    Thanks
    0
    Thanked 1 Time in 1 Post
    it will work but make sure you have the chip flashed to 2.3 firmware otherwise you will have to solder the one J wire.

  4. #4
    Junior Member
    Join Date
    Aug 2008
    Location
    Somerset, KY
    Posts
    14
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Can I use a D2pro9v3 on an older Wii ?

    I bought a new wii with the D2E chipset and installed a D2pro9v3 but had to solder in the J wire. Works great.

    D2Pro9 V2 / V3 Bundle (D2Pro9 V3 + V4C WiiClip + Triwing Screwdriver)

    Now my brother in law wants me to do the same on his 1-2 year old wii (serial no. LU301040866). According to the site to check this serial number it is an 84% chance it is a D2B chipset.

    Since I had a D2E and have not flashed it to 2.3 (since you can't do that on D2E chipsets from what I read), I soldered the J wire.

    Can I purchase a D2pro9v3 presoldered to the clip like mine was and use it on his older possible D2B wii?

    Should I use a cheaper mod chip for an older system. I would rather keep the soldering to 0% but can if I must (I'm an electrical engineer too).

    I just want to make it simple like the D2pro9v3 was for my new wii.
    Last edited by tdg8934; 08-31-2008 at 07:30 AM.

  5. #5
    New Member §piktsµ's Avatar
    Join Date
    May 2008
    Location
    Orlando, FL - USA
    Posts
    548
    Thanks
    6
    Thanked 24 Times in 22 Posts
    If that D2B Wii has the legs cut then u wont be able to use a Wii-Clip..
    I would use the WiiKey and install it by dremelling the chip set.. (check out my pics)
    or I could use the D2Sun, D2pro9rev3 or the newest D2E A9 mod chip..
    On that case I wouldnt have to dremell the Chipset.. anyways.. i guess tell your
    brother law his options.. check out my thread for more info on pricing.. and shipping
    would be $15. (if you are in the states). I would ship it off the same day i receive it..
    The Wii would get modded the day it arrives..


  6. #6
    Junior Member
    Join Date
    Aug 2008
    Location
    Somerset, KY
    Posts
    14
    Thanks
    0
    Thanked 0 Times in 0 Posts

    No solderless option for D2B with cut wires??

    Is there no solderless option available for a D2B Wii with the cut wires? The serial number link said there was also an 84% chance it has the 3 cut wires.

    Seem's like the Wii key is the cheapest option for the D2B chipsets if I must solder the wires. Hopefully there is a solution for solderless.

    Comments?

  7. #7
    New Member §piktsµ's Avatar
    Join Date
    May 2008
    Location
    Orlando, FL - USA
    Posts
    548
    Thanks
    6
    Thanked 24 Times in 22 Posts
    Unfortunately not.. if you have the cut leg version of the D2B then your only option
    is going with the wire/solder way.. I coud install either the WiiKey or
    the D2E A9 (newest modchip in the market) compatible with all the Wii DVD Drives.
    Let me know what your brother law decides.. tell him to call me if he doesnt feel
    comfortable in shipping his Wii.. or read my feedbacks, perhaps then he'll feel ok

  8. #8
    Junior Member
    Join Date
    Aug 2008
    Location
    Italy - Europe
    Posts
    16
    Thanks
    0
    Thanked 0 Times in 0 Posts
    The console has model number RVL-001(USA), produced for Canada/Mexico/USA.

    * There is a 75% chance the chipset is GC2-D2C (v1).
    * And there is also a 25% chance the chipset is GC2-D2B with cut pins and missing third pad.

  9. #9
    New Member §piktsµ's Avatar
    Join Date
    May 2008
    Location
    Orlando, FL - USA
    Posts
    548
    Thanks
    6
    Thanked 24 Times in 22 Posts
    Yeah if you have a D2Cv1 chipset i would go with the D2E A9, D2Sun or D2pro9rev3.
    it would be a nine wire install ..it would look like this.. here's the D2Sun.


  10. #10
    Junior Member
    Join Date
    Aug 2008
    Location
    Somerset, KY
    Posts
    14
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Have a DMS (not D2B) and another one - D2C

    I got home from my brother in laws house (8 hour drive) for the holiday weekend. I have 2 wii's from him. What I thought was a D2B based on the serial number check was actually a DMS (once opened up and verified by me). My other brother in law wanted me to install a modchip into his wii. His was not as old and it had a D2C.

    OK - Can I use the D2pro9v? with a solderless snap on clip with these?

    Or is there a cheaper solution less having to solder all the wires - like the wii-key? I read that the wii-key V3 solderless clip works on DMS/D2A/D2B but wont work if the console has the "3 cut pins". Is this only a problem on D2B or how do I tell if the DMS has the "3 cut pins"?


    Thanks!
    Last edited by tdg8934; 09-01-2008 at 02:45 PM.

Page 1 of 2 12 LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •