Page 1 of 2 12 LastLast
Results 1 to 10 of 19

Thread: Solderless D2Pro Anyone had a problem

  1. #1
    Junior Member
    Join Date
    Aug 2008
    Posts
    15
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Solderless D2Pro Anyone had a problem

    I just recently bought this chip to mod my wii, so far no luck w/any of the games I have burned. Not sure if this modchip is working or not. Anyway to tell if it is? I have burned 3 games at various speeds, different media, using ImgBurn and good media Taiyo Yuden, TDK. Have ordered some Verbatim to try. Does anyone have a backup copy that I could test my Wii with?

    When I put in the game disc it just spins and spins, finally get a message "unable to read disc". Any advise what to try next.


    Anyone else having trouble with the Solderless D2Pro chip?

  2. #2
    Junior Member
    Join Date
    Jun 2008
    Posts
    34
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by madgreen View Post
    I just recently bought this chip to mod my wii, so far no luck w/any of the games I have burned. Not sure if this modchip is working or not. Anyway to tell if it is? I have burned 3 games at various speeds, different media, using ImgBurn and good media Taiyo Yuden, TDK. Have ordered some Verbatim to try. Does anyone have a backup copy that I could test my Wii with?

    When I put in the game disc it just spins and spins, finally get a message "unable to read disc". Any advise what to try next.


    Anyone else having trouble with the Solderless D2Pro chip?
    Yeah I had the same problem. Was told 0% chance to have to solder the J wire until I told them it didn't work and only lit up red on the chip.

  3. #3
    Reading Room
    Join Date
    May 2008
    Posts
    414
    Thanks
    0
    Thanked 1 Time in 1 Post
    unbridge the ck and solder the j wire to the chip and the board as per image below

    http://www.wii-clip.com/images/V4C_D2Pro_9wires-8.jpg

  4. #4
    Wiihacks Recommended
    Pro Installer/Store
    Senior Member
    Spyman's Avatar
    Join Date
    Jun 2008
    Location
    Greater Toronto Area
    Posts
    1,546
    Thanks
    33
    Thanked 123 Times in 106 Posts
    what is the behaviour of the leds, could just be a bad burn.
    Send me a PM if you need any Canadamods.ca support

    $9.95 Flat Rate Shipping to Canada & USA
    Official Support for Canadamods. I am here to help.

    email: sales@canadamods.ca | website: http://www.canadamods.ca | Phone: +1 416 728 0648

    We are the Official Distributors for: P.3Key, Wode JukeBox, WasabiDX, WiiKey, DriveKey, M3i & More - Always Authentic Guarenteed !
    Buy Wode JukeBox v2.0 here: Here

  5. #5
    Junior Member
    Join Date
    Aug 2008
    Posts
    15
    Thanks
    0
    Thanked 0 Times in 0 Posts
    My wii is a GC2-D2C, what is yours? Why would it require the wire to be soldered?

  6. #6
    Junior Member
    Join Date
    Aug 2008
    Posts
    15
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Why would my unit require this J wire, mine is a GC2-D2C, purchased in March? I will take it apart and look and LED, with the cardboard on you can't really see it. thanks

  7. #7
    Reading Room
    Join Date
    May 2008
    Posts
    414
    Thanks
    0
    Thanked 1 Time in 1 Post
    depending on ur led colors ...if its solid red then u will probably need to solder j wire and unbridge ck as per the wii clip site....

  8. #8
    Junior Member
    Join Date
    Aug 2008
    Posts
    15
    Thanks
    0
    Thanked 0 Times in 0 Posts
    I took my unit apart and powered up and the light is red. Are you saying that I need to "unbridge" the clk-when I view the clk there is a divide already in the clk area-so does that mean it is already "unbridged". Then you are saying to solder the wire across and that should fix my problem? Will it harm the Wii unit to do this?

  9. #9
    Junior Member
    Join Date
    Aug 2008
    Posts
    15
    Thanks
    0
    Thanked 0 Times in 0 Posts
    My light LED is red, and I have noticed that the clip on the chip is W-clip w/the no's. below are V4C-9, is the clip a fake and would I be able to send it back to the company where I bought it, which was techsick.com?

  10. #10
    Reading Room
    Join Date
    May 2008
    Posts
    414
    Thanks
    0
    Thanked 1 Time in 1 Post
    unbridge ck and solder j wire

Page 1 of 2 12 LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •