Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Ejecting/Installation problems

  1. #1
    Junior Member
    Join Date
    Jul 2008
    Posts
    28
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Ejecting/Installation problems

    I've been trying to install my d2pro9 v2 self solder on my d2c2 with a lot of failures. All of the problems have been that the DVD wouldn't eject back out after putting the DVD in.

    I tried applying the long C wire trick this time on the install (http://www.wiihacks.com/d2pro9/4674-...blems-fix.html). It began to work at first for about 4-5 ejects then after that it gave me a black screen to eject the disc, turn off the power, and refer to manual.

    I was roaming around wiinewz.com forums and noticed that people have soldered the C point directly to the leg instead of the one on the d2pro team diagram, should I give that a try or it doesn't matter? Also any other advice would be great.

  2. #2
    Reading Room
    Join Date
    May 2008
    Posts
    414
    Thanks
    0
    Thanked 1 Time in 1 Post
    have u tried the fix from little johnny?

    http://www.wiihacks.com/d2pro9/4674-...blems-fix.html

  3. #3
    Wiihacks Recommended
    Pro Installer/Store
    Senior Member
    Spyman's Avatar
    Join Date
    Jun 2008
    Location
    Greater Toronto Area
    Posts
    1,546
    Thanks
    33
    Thanked 123 Times in 106 Posts
    i always solder the c directly to the IC, give it a shot, the long clk will help also. Johnnys trick works sometimes also.
    Send me a PM if you need any Canadamods.ca support

    $9.95 Flat Rate Shipping to Canada & USA
    Official Support for Canadamods. I am here to help.

    email: sales@canadamods.ca | website: http://www.canadamods.ca | Phone: +1 416 728 0648

    We are the Official Distributors for: P.3Key, Wode JukeBox, WasabiDX, WiiKey, DriveKey, M3i & More - Always Authentic Guarenteed !
    Buy Wode JukeBox v2.0 here: Here

  4. #4
    Junior Member
    Join Date
    Aug 2008
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    are you sure none of your points are touching? i was getting the same error b/c my D point had come off and was crossing some pins

  5. #5
    Junior Member
    Join Date
    Jul 2008
    Posts
    28
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Nah, none of the points are touching, checked many times for that. I'll probably try Little Johnny's fix for alternate D E F points and 1.5v fix.

  6. #6
    Junior Member
    Join Date
    Jul 2008
    Posts
    28
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Question about Little Johnny's 1.5v fix. Do you have to use the other alternate ground point if you apply the 1.5v point or is it fine with just default ground point on the d2pro.com diagram?

  7. #7
    Reading Room
    Join Date
    May 2008
    Posts
    414
    Thanks
    0
    Thanked 1 Time in 1 Post
    default ground point is fine

  8. #8
    Junior Member
    Join Date
    Jul 2008
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    I'm having the same problem with the D2Pro9 + Wii Clip I just installed in my Wii. It worked OK for the first few times I used it after being chipped. Now, when it does load a disc (any), it won't recognize it, just presents the black screen with instructions that was mentioned above. Also, I have to cycle the power several times to get the disc to eject. And these are original game discs, not copies.

    Any ideas? I feel like I just wasted my $80 on this chip and other than trying to reseat the chip, I don't know what else I can do?

    Thanks.
    Last edited by Ghostryder; 08-18-2008 at 01:33 PM.

  9. #9
    Reading Room
    Join Date
    May 2008
    Posts
    414
    Thanks
    0
    Thanked 1 Time in 1 Post
    the new firmware came out which fixes the eject issues......do u have the 3.3 firmware update? could be a reason why ur getting that error message as well if game is trucha signed

  10. #10
    Junior Member
    Join Date
    Jul 2008
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by GMODZ View Post
    the new firmware came out which fixes the eject issues......do u have the 3.3 firmware update? could be a reason why ur getting that error message as well if game is trucha signed
    I'm not sure how I can determine what rev FW the chip is running? Would you mind pointing me to the right place to find the FW?

    Thanks.

Page 1 of 2 12 LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •