Page 1 of 17 12311 ... LastLast
Results 1 to 10 of 169

Thread: Infectus Nand Flashing Guide

  1. #1
    Junior Member streamlinehd's Avatar
    Join Date
    Mar 2010
    Location
    East Coast, USA
    Posts
    1,369
    Thanks
    114
    Thanked 557 Times in 377 Posts
    Blog Entries
    3

    Infectus Nand Flashing Guide

    WARNING: This Is An Advanced Guide.... If you don't understand everything here, I recommend you do not proceed as this is advanced brick repair and is not a suitable option for most bricks. Please consider ALL other options before continuing with this method.(C) streamlinehd 2010 - streamlinehd@gmail


    Chapter 1 - What You Should Know Before You Start(C) streamlinehd 2010 - streamlinehd@gmail


    Nand flashing isn’t for everyone and there are many factors you should consider before attempting to follow this guide. First and foremost, you must have excellent mechanical and problem solving skills. If you’ve never done any type of electronics repair work before, this is not a good place to start. Secondly, doing this for the repair of a single console isn’t at all practical. The costs involved in acquiring the required tools and equipment to successfully complete this task can easily exceed the cost of a brand new console. Lastly, you should consider the fact that the vast majority of people who attempt to flash their Wii fail. This is my one and only warning and I strongly suggest you read this guide thoroughly and think this all over before continuing.(C) streamlinehd 2010 - streamlinehd@gmail

    I’m writing this guide with hopes of helping more people to succeed as a lot of the fail has to do with the information available. Some guides on this topic are even setup for failure however most people place self blame and wind up giving up. As mentioned in the warning above, this is advanced brick repair and I've done my best to keep the process as simple as possible in this step by step tutorial. If you have a question not covered or get stuck on a step, post your question or issue in this guide. Please do not open separate threads or PM me as this won't help other members having a similar problem.


    FAQ



    vx2k7b5atVoc48DulOPoXM63UIWreydK34tNP31vvbdaNNKub6 nhOoySd3q5ahzfsJDJlOGavp8xLw7gzT+JgvjZceNKmn0P1GOS JnCwyKYGUj+rUh9bDSe5/zHqTjVE
    What you need to know About Boot1 and Boot2 before you start
    (C) streamlinehd 2010 - streamlinehd@gmail(C) streamlinehd 2010 - streamlinehd@gmail
    • Boot1a, boot1b = Boot2 Bootmii Compatible (Bootmii ARM can be injected into boot2)

    • Boot1c, boot1d = Not Boot2 Bootmii Compatible (You will need a NAND backup or keys that was created with Bootmii).

    • Boot2 can not be downgraded but can be updated.


    If your Wii is boot2 Bootmii compatible
    (C) streamlinehd 2010 - streamlinehd@gmail(C) streamlinehd 2010 - streamlinehd@gmail
    • You will need the boot blocks from a donor NAND with the Bootmii ARM code injected into boot2. If you don't have a donor you can use my Boot Patcher program to generate the boot blocks.


    (C) streamlinehd 2010 - streamlinehd@gmail
    If your Wii is not boot2 Bootmii compatible you will need:

    • (a.) working nand backup from the bricked Wii

    • (b.) donor nand backup from another Wii and the keys from your bricked Wii.


    NOTE: If you don’t know what version of Boot1 is installed on your Wii you can try using WiiNand v0.2 to detect your boot1 version. For some reason WiiNand can’t always detect the boot1 version and unfortunately there’s no other program that will do this ATM. EDIT: New WiiFlash Toolz v0.0.0.1 will detect all boot1 and boot2 versions. If you know how to use a hex editor you can also compare the boot1 blocks from a known nand to figure out what boot version you have.(C) streamlinehd 2010 - streamlinehd@gmail


    Chapter 2 - Getting Started NAND Flashing Tutorial(C) streamlinehd 2010 - streamlinehd@gmail


    Step 1 – Acquiring the required tools/software

    You will quickly find that this type of work is a dying trade and gathering all the required tools and equipment is not such an easy task. Here’s a complete list of the tools/equipment and software you will need before you continue. I recommend downloading all the software and putting it in an easily accessible folder on your computer.

    Password for Downloads



    1. Infectus Programmer Software v3.9.9.0(C) streamlinehd 2010 - streamlinehd@gmail

    2. Xavbox Software v1.0.0.7

    3. Libusb devel filter 1.2.2.0

    4. Hex Editor (I use Hex editor Neo)(C) streamlinehd 2010 - streamlinehd@gmail

    5. WiiFlash Toolz v0.2

    Tools & Equipment



    Step 2 – Putting Infectus Into NAND Programming Mode

    Note: When you first connect Infectus to your computer and open the Infectus Programmer Software you may be asked to perform an update. You should accept this update and wait for it to complete as you won't be able to continue until you do. Don't worry if you don't receive a message saying the update is complete because the update will start over again if it doesn't complete properly.
    (C) streamlinehd 2010 - streamlinehd@gmail(C) streamlinehd 2010 - streamlinehd@gmail
    1. Download and extract the Infectus Programmer Software v3.9.9.0 to a convenient location on your computer.(C) streamlinehd 2010 - streamlinehd@gmail

    2. Connect the Infectus to the USB programmer and plug it into your computer. The new device detection wizard should open. Choose to browse for device software and install the Infectus drivers manually from the folder you extracted them to (e.g. C:\InfectusProgrammer-3.9.9.0\USB-Drivers3.1).(C) streamlinehd 2010 - streamlinehd@gmail

    3. Open the Infectus Programmer software and you should see a message at the bottom which says Board: Infectus 1/2. Select the menu option Actel Firmware and select NAND programmer. Then select program located at the bottom of the same drop down menu.(C) streamlinehd 2010 - streamlinehd@gmail

    4. The software will begin programming the Infectus into NAND programming mode. Wait for this process to complete and then close the Infectus software.





    Step 3 – Remove Infectus Drivers and Install Xavbox


    1. Download and extract the Xavbox Software v1.0.0.7 to a convenient location on your computer.

    2. Launch the Setup Wizard and follow instruction to install Xavbox to your computer.

    3. Remove the Infectus drivers by locating your device manager, right clicking on Infectus device and choosing uninstall (see image below). A dialog box will appear to confirm you want to delete the software, select the box that says delete the driver software for this device and click OK.(C) streamlinehd 2010 - streamlinehd@gmail



    4. Unplug the Infectus from your computer and plug it back in. Go back to Device Manager, locate USB API, right click on it and choose update driver software. Choose to brows your computer for the drivers and navigate to the location you extracted them to (e.g. C:\Xavbox_v1.0.0.7\Drivers).(C) streamlinehd 2010 - streamlinehd@gmail

    5. Download LibUSB-Win32 Setup Wizard and install the software. When the software finishes installing, choose to launch the filter installer wizard and click finish.

    6. Choose to install a device filter and click next. Locate USB Composite Device with pid: 4f11, if you see multiple devices with the same ID, look for the one that says Standard USB Host Controller select it and click Install.

    7. Xavbox is now ready to work properly with your Infectus device.(C) streamlinehd 2010 - streamlinehd@gmail


    Step 4 – Connecting Infectus to Your NAND

    There are three methods to connecting the Infectus to your NAND. These methods include; (1) on-board programming by soldering to the legs of the NAND, (2) on-board programming by soldering to the vais of the motherboard and (3) external programming via TSOP adapter. I recommend removing the NAND from the motherboard and programming it externally with a TSOP Adapter. I’ve personally found this the best way to program since it’s a direct connection to the NAND which means the chances for data corruption are lessened. The other two methods are on board programming methods which requires pin-point soldering skills or making 18 very frustrating connections to the vias of the motherboard. I don't recommend using the on-board methods because they require above average soldering skills and you are much more likely to have data corruption using these methods. That being said, this guide will focus on the external programming method via TSOP adapter.

    External Programming via TSOP48 Adapter(C) streamlinehd 2010 - streamlinehd@gmail

    In order to connect Infectus to your NAND externally you will need to solder 19 wires from the Infectus to your TSOP48 adapter. This requires moderate soldering skills and the use of a continuity meter in order to ring out each pin of the adapter to the correct soldering points. Use the wiring diagrams below for reference.

    NOTE: You will have to carefully remove your NAND from the motherboard using a Hot Air Rework station to complete this method. To do this properly, I recommend applying a few drops of no clean flux and heating each side of the NAND for about 30-45 seconds while lightly prying the chip away from the motherboard. You should use the temperature and fan speed settings that best suit your Hot Air station for proper SMD removal.(C) streamlinehd 2010 - streamlinehd@gmail(C) streamlinehd 2010 - streamlinehd@gmail

    Programming The NAND Externally Wiring Diagrams (Recommended Method)



    Programming The NAND On-Board Wiring Diagrams (Not Recommended)




    Step 5 – Testing Read/Write Capabilities

    1. With Infectus connected to your computer open up Xavbox and choose Detect USB, then select Open. Your screen should look like this:



    2. Press Ident and the Blocs, Pages, Bytes and Spare boxes will automatically populate with the correct information. Your screen should now look like this: (If you receive any errors at this point see troubleshooting)(C) streamlinehd 2010 - streamlinehd@gmail



    3. If you haven't received any errors to this point, congratulations you made all your connections properly and Xavbox is ready to read your NAND. Now press Destination and set a destination path for your first read/write test and name the file flash.bin (e.g. C:\User\desktop\flash.bin)

    4. Set the parameters to start at block 4080 and end at block 4095 and then press read. This will read blocks 4080-4095 of the NAND and write them to the file specified.(C) streamlinehd 2010 - streamlinehd@gmail

    5. Write blocks 4080-4095 back to the NAND by putting the file you just made (flash.bin) in the Source box and setting the parmaters to start at block 4080 and end at 4095. Also select the relative offset checkbox.

    6. Now choose the Update and Compare write option and press Write. If all the blocks write to the NAND successfully without a compare error, you are good to go and this test was successful. If you do have a compare error and the write fails, see the troubleshooting section of this guide and do not continue!!.

    IMPORTANT: A different block message (e.g. block 1 different) in the results window is not a compare error. A compare error will end the writing process at the block that didn't write/compare properly.


    Step 6 – Flashing The NAND(C) streamlinehd 2010 - streamlinehd@gmail


    A.) Flashing Boot2 With Bootmii ARM

    1. First make a full dump of the NAND by selecting a destination path and setting the parameters to start at block 0 and end at block 4095. Choose to read those blocks and wait for this step to complete. Please note that this process will take a while to finish.

    2. Make a copy of the full NAND dump and put the original file in a folder not to be touched unless needed. This will serve as a backup just in case you make any mistakes when writing to the NAND.

    3. Determine Which version of Boot1 is on the NAND by opening the copy of your full dump with WiiFlash Toolz. You can also open the dump with a hex editor and check the value of offset 40 to determine the boot1 version: (see picture below)

    @ Offset 40 a value of 99 = Boot1a, c1 = boot1b, fc= boot1c, and 48 = boot1d (C) streamlinehd 2010 - streamlinehd@gmail
    The example below shows that the NAND has boot1b installed.

    (C) streamlinehd 2010 - streamlinehd@gmail

    4. Get a donor NAND dump with Bootmii injected into boot2 and use WiiFlash Toolz to extract the boot blocks. Keep in mind that the boot1 version from the donor NAND must match the boot1 version of the target NAND and boot2 can match the target NAND or can be upgraded to boot2v4.

    5. In Xavbox load the boot blocks you just generated with WiiFlash Toolz to the source input and then set the parameters to start at block 0 and end at block 7.

    6. Choose Update and Compare and then press the Write button. This will update/compare the boot blocks and inject Bootmii into boot2 (If you receive a compare error see the troubleshooting section of this guide).

    (C) streamlinehd 2010 - streamlinehd@gmail

    7. The NAND now has Bootmii flashed into boot2 and is ready to refit to the motherboard.


    B.) Flashing Backup NAND - Non-boot2 Compatible Consoles(C) streamlinehd 2010 - streamlinehd@gmail


    1. In Xavbox load your Bootmii backup (nand.bin) to the source input and then set the parameters to start at block 0 and end at block 4095.

    2. Choose Update and Compare and then press the Write button. This will update/compare any different blocks on the NAND with the data from your backup. This process can take a quite a while to complete (If you receive a compare error see the troubleshooting section of this guide).(C) streamlinehd 2010 - streamlinehd@gmail

    3. The NAND has now been flashed with your working backup and is ready to refit to the motherboard.


    C.) Flashing Donor NAND - Must have keys from bricked Wii


    1. Follow the Betwiin Guide to encrypt the donor NAND with the bricked Wii's Keys and then continue to follow this guide. If you have a question on how to use Betwiin, please post in the guide and do not post those questions here.

    2. In Xavbox load your Bootmii backup (nand.bin) to the source input and then set the parameters to start at block 0 and end at block 4095.

    3. Choose Update and Compare and then press the Write button. This will update/compare any different blocks on the NAND with the data from your backup. This process can take a quite a while to complete (If you receive a compare error see the troubleshooting section of this guide).(C) streamlinehd 2010 - streamlinehd@gmail

    4. The NAND has now been flashed with your working backup and is ready to refit to the motherboard.


    Step 7 – Refitting NAND To Motherboard


    1. Clean the NAND solder pads on the motherboard with de-soldering braid (wick) so that you have a clean and smooth surface to solder to.

    2. Follow this video tutorial to refit the NAND to the motherboard.

    vx2k7b5atVoc48DulOPoXM63UIWreydK34tNP31vvbdaNNKub6 nhOoySd3q5ahzfsJDJlOGavp8xLw7gzT+JgvjZceNKmn0P1GOS JnCwyKYGUj+rUh9bDSe5/zHqTjVE

    Troubleshooting

    Troubleshooting




    Credits



    vx2k7b5atVoc48DulOPoXM63UIWreydK34tNP31vvbdaNNKub6 nhOoySd3q5ahzfsJDJlOGavp8xLw7gzT+JgvjZceNKmn0P1GOS JnCwyKYGUj+rUh9bDSe5/zHqTjVE
    Last edited by streamlinehd; 11-15-2011 at 04:12 PM.
    Cogita ante salis
    If you're happy with the help I provided, don't forget to hit my thanks button



  2. #2
    Retired WiiHacks Staff Krafter's Avatar
    Join Date
    Dec 2009
    Posts
    4,426
    Thanks
    460
    Thanked 1,093 Times in 857 Posts
    Blog Entries
    5
    Excellent work my friend.

  3. 2 Users Say Thank You to Krafter For This Useful Post


  4. #3
    Member
    Join Date
    Jan 2009
    Posts
    2,692
    Thanks
    254
    Thanked 396 Times in 369 Posts
    brilliant !
    am looking for an used Infectus module, as hobby and have fun
    if anyone like to offer.....

  5. 1 User Says Thank You billyhome For This Useful Post


  6. #4
    Junior Member
    Join Date
    Dec 2009
    Location
    England
    Posts
    1,304
    Thanks
    7
    Thanked 320 Times in 240 Posts
    Blog Entries
    2
    we have 3 infectus guides now, can we remove some of the others?

    this is far clearer and there is no point having the same thing 3 times.

    and billy, diveneo sell them cheaper than you will likely pick it up used.

    also, the infectus isnt competing with hollywood, as you short to stop hollywood booting, so no data lines are in use - despite what deadlyfoez says. this is standard practice for any on board programming - put cpu into a reset state, so you are free to use the flash/nand for reprogramming.

    oh also, why do a update and then verify? just do a "update and compare" which does it all in 1, and also tells you if theres a problem as it happens
    Last edited by Krank; 01-14-2011 at 10:45 AM.

  7. 1 User Says Thank You Bad_Ad84 For This Useful Post


  8. #5
    Senior Member
    WiiHacks Staff
    Senior Moderator
    Only site donators may send a PM to WiiHacks Staff
    oddgriffin's Avatar
    Join Date
    Nov 2009
    Location
    New Franklin, Ohio. USA
    Posts
    10,193
    Thanks
    2,206
    Thanked 2,579 Times in 2,012 Posts
    Blog Entries
    2
    Yes we will need to move other simular guides to an archive section, especially since at least one wasn't being supported by it's author as he was too arrogant to be bothered to do that lol.
    Sent from my van, down by the river.




    Never quantify your life by comparison. It is always going to be apples to oranges. If you feel the need to always look down on others, you currently do not own enough mirrors------ Tommie Griffin.

  9. 1 User Says Thank You oddgriffin For This Useful Post


  10. #6
    Member
    Join Date
    Jan 2009
    Posts
    2,692
    Thanks
    254
    Thanked 396 Times in 369 Posts
    Bad_Ad84,
    i really want to thank you again, for telling me about diveneo. i have noted your words in other thread, before.
    yup, i'll get it from diveneo in my coming home visit.

  11. 1 User Says Thank You billyhome For This Useful Post


  12. #7
    New Member freestile's Avatar
    Join Date
    Oct 2010
    Posts
    132
    Thanks
    23
    Thanked 6 Times in 6 Posts
    Hope I never have to do all this. This would have to be the last resort. I guess its not called "advanced brick repair"
    for nothing. Good guide streamlinehd.

  13. 1 User Says Thank You freestile For This Useful Post


  14. #8
    Junior Member
    Join Date
    Dec 2009
    Location
    England
    Posts
    1,304
    Thanks
    7
    Thanked 320 Times in 240 Posts
    Blog Entries
    2
    bootblocks

    bootblocks.rar

    and while on the subject of archiving tutorials.

    http://www.wiihacks.com/bricked-wii-...brick-fix.html
    and
    http://www.wiihacks.com/bricked-wii-...tion-here.html

    do the same thing, id recommend archiving the second and editing the first slightly.


    also:
    "5. Write blocks 4080-4095 back to the NAND by putting the file (flash.bin) in the Source box and setting the parmaters to start at block 4080 and end at 4095. Then choose the All and Compare write option and press Write. If all the blocks write to the NAND successfully without a mismatch, you are good to go and this test was successful. If you do have a mismatch see the troubleshooting section of this guide and do not continue!!."


    This part is wrong, you shouldnt do "all and compare" when the target chip isnt blank, you need to erase before a program. this should be "update and compare" as this reads the block, compares to buffer, erases if needed, writes then compares.
    Last edited by Bad_Ad84; 01-14-2011 at 04:54 AM.

  15. 1 User Says Thank You Bad_Ad84 For This Useful Post


  16. #9
    Junior Member
    Join Date
    Dec 2009
    Location
    England
    Posts
    1,304
    Thanks
    7
    Thanked 320 Times in 240 Posts
    Blog Entries
    2
    NOTE: You will have to carefully remove your NAND from the motherboard using a Hot Air SMD Rework station to complete this method. To do this properly, I recommend applying a few drops of no clean flux and heating each side of the NAND for about 30-45 seconds while lightly prying the chip away from the board. The hot air should be set between 300-400 degrees and the fan speed should be set between 8 - 10.


    This is all very equipment specific and should be removed IMO.

    For instance, my hot air station only goes upto 8 for air speed and I have mine set on approx 3.2, my heater also isnt in degrees, but due to the lower speed of the air my heat is set much lower - 3.6 out of 8 on mine. It is set this way intentionally so you do not desolder and blow off smaller parts (caps/resistors) with the air flow.

    If someone has a hot air station, I would suggest they know what temps they need to desolder something.

    edit:
    also, dont think that im knocking your guide - you should know how i post by now, i just like this to be as correct as possible and im just putting forward my input. i find this guide much clearer than the others and is how I would of done this guide had deadlyfoez removed his.
    Last edited by Bad_Ad84; 01-14-2011 at 08:38 AM.

  17. 1 User Says Thank You Bad_Ad84 For This Useful Post


  18. #10
    WiiHacks Staff
    Only Site Donators Can PM Staff
    Forum Administrator
    IRC AOP
    Wall-Eyed Mucksucker
    emuhack's Avatar
    Join Date
    Aug 2009
    Location
    Windy City
    Posts
    7,473
    Thanks
    892
    Thanked 2,132 Times in 1,347 Posts
    Blog Entries
    13
    Quote Originally Posted by Krafter View Post
    Excellent work my friend.
    Could not have said it Better!!!!

    AMAZING!!!!!

    If someone has a hot air station, I would suggest they know what temps they need to desolder something.
    Mine i use @ 400 degrees and there is no fan speed, but it takes about 30-45 sec of going side to side to GENTLY remove the 24 legs on the one side then "rinse and repeat" on the other side....

    Last edited by emuhack; 01-14-2011 at 08:40 AM.

  19. 1 User Says Thank You emuhack For This Useful Post


Page 1 of 17 12311 ... LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •