Page 3 of 3 FirstFirst 123
Results 21 to 25 of 25

Thread: wii brick ??

  1. #21
    Senior Member
    DA KINE WiiHacker
    mauifrog's Avatar
    Join Date
    May 2009
    Posts
    9,191
    Thanks
    307
    Thanked 9,585 Times in 2,974 Posts
    Blog Entries
    15
    Try to replace your settings.txt
    Backup and format your sd-card
    Extract CB2_BB_System-Settings-Replace_MOD.zip to the card
    Then copy the settings.txt for NTSC or PAL to the root sd:\
    Settings.txt is in the folders sd:\ntsc and sd:\pal, pick your region.
    Then insert the card and boot the wii, install the new settings.txt.

    Hopefully that should do the trick. The wii will boot, if not run CB2_BB_SignCheck.zip again. We should see the unkown region change to your region.

    If that does fail,
    Use cboot2_wadmanager_1.5_mod.zip with ios249


    Install IOS60-patched.zip first
    Then
    Install your system menu wad- for your region, second
    4.1U-RVL-WiiSystemmenu-v449.wad
    or
    4.1E-RVL-WiiSystemmenu-v450.wad

    U= USA ntsc
    E= Euro pal

    If none of this works, you may have a hardware issue. It is not your bluetooth, but as mentioned earlier, it could be your wifi or drive. Wii Brick Flowchart

    Also, be sure to test booting into the system menu from bootmii. Verify your bootmii config is set to autoboot system menu, delay of 0 and proper display.
    Ipsa scientia potestas est.


    Warning: Piracy is NOT supported. Word your questions carefully.

  2. 1 User Says Thank You mauifrog For This Useful Post


  3. #22
    Junior Member
    Join Date
    Dec 2009
    Posts
    10
    Thanks
    9
    Thanked 0 Times in 0 Posts
    tryed the above nothing worked so i used the comex formatter and it worked only its now in pal i guess i copyed the wrond files but i do get the system menu and every thing i think played with it for a while got it to stop flippin so i have a 3.1e wii with system menu can i use any region hacker to fix it

  4. #23
    Senior Member
    DA KINE WiiHacker
    mauifrog's Avatar
    Join Date
    May 2009
    Posts
    9,191
    Thanks
    307
    Thanked 9,585 Times in 2,974 Posts
    Blog Entries
    15
    Quote Originally Posted by justin4102 View Post
    tryed the above nothing worked so i used the comex formatter and it worked only its now in pal i guess i copyed the wrond files but i do get the system menu and every thing i think played with it for a while got it to stop flippin so i have a 3.1e wii with system menu can i use any region hacker to fix it
    Just do step 1 and 3 of the 3.1-4.1 guide linked below.

    Then

    Backup and format your sd-card
    Extract CB2_BB_System-Settings-Replace_MOD.zip to the card
    Then copy the settings.txt for NTSC to the root sd:\
    Settings.txt is in the folders sd:\ntsc
    Then insert the card and boot the wii, install the new settings.txt.

    Then
    Use CB2_BB1_WadManager_1.4.zip with ios249


    Install IOS60-patched.zip first
    Then
    Install your system menu wad- for your region, second
    4.1U-RVL-WiiSystemmenu-v449.wad

    Then do step 5 of the 3.1-4.1 guide linked below, then do a nand backup

    Alternatively you could use any region changer and go to 3.2u
    Last edited by mauifrog; 01-02-2010 at 05:06 PM.
    Ipsa scientia potestas est.


    Warning: Piracy is NOT supported. Word your questions carefully.

  5. 1 User Says Thank You mauifrog For This Useful Post


  6. #24
    Junior Member
    Join Date
    Dec 2009
    Posts
    10
    Thanks
    9
    Thanked 0 Times in 0 Posts
    FIXED i used the comex formatter toll got 3.1e because i made a mistake played with setting and got it to display 480i resolution then i tryed using the anyregion changer it gave me an error then i used the cboot2 wad manager and installed 3.2u i know this would put it in a brick state i then used the settings mod u gave me earlier and bam i have 3.2u and a fully working wii.

  7. #25
    Senior Member
    DA KINE WiiHacker
    mauifrog's Avatar
    Join Date
    May 2009
    Posts
    9,191
    Thanks
    307
    Thanked 9,585 Times in 2,974 Posts
    Blog Entries
    15
    Quote Originally Posted by justin4102 View Post
    FIXED i used the comex formatter toll got 3.1e because i made a mistake played with setting and got it to display 480i resolution then i tryed using the anyregion changer it gave me an error then i used the cboot2 wad manager and installed 3.2u i know this would put it in a brick state i then used the settings mod u gave me earlier and bam i have 3.2u and a fully working wii.
    That works as well.
    Ipsa scientia potestas est.


    Warning: Piracy is NOT supported. Word your questions carefully.

Page 3 of 3 FirstFirst 123

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •