Results 1 to 2 of 2

Thread: Brick while updating from 4.0-4.1 | BootMii as IOS | No NAND Backup

  1. #1
    Junior Member
    Join Date
    May 2009
    Posts
    2
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Brick while updating from 4.0-4.1 | BootMii as IOS | No NAND Backup

    I was running through dogeggs' tutorial below, and got to step 4 - installed patched IOS60; then during 4.1 update (from 4.0), lost power to the Wii and ended up with what looks like a banner brick - corrupted system files screen shows, but seems to have large blocks missing, making it hard to read (weird). BootMii had to be installed as an IOS earlier in the process.

    Is there any chance I can unbrick this with an UUB and SaveMii (or modded GC controller), but without installing a mod chip? I suppose any option is on the table at this point.

    Oh, there's no NAND backup of course - wasn't enough room on the SD card (stupid me).

    I'll itemize this if it helps any:
    - Apparent banner brick (shows system file corrupt)
    - BootMii installed as IOS
    - No NAND backup
    - cIOS38 r14 installed
    - Power loss while waiting for 4.0-4.1 system menu update in step 4 is apparent cause of brick
    - No mod chip

    Thanks.

    Code:
    This guide will fully modify your Wii to safely play backup games, it works on all wiis up to 4.1 regardless of serial number/region etc this includes boot2 v4 Wiis aka 'LU64-65' models, If you bought your Wii this year and it came with 3.4+ on it then it will be a boot2 v4.
    
    If you are on 4.2 then do this excellent guide by messie to modify your Wii.
    
    There is a new DVD drive chipset that is starting to emerge that will not play DVDR, if your Wii came with sys menu 4.0 on it then it could be one, the chipset is known as a D3-2 and the only way of telling if you have one is to open her up, but as this will invalidate your warranty you are better off trying to load DVDRs and if you just keep getting errors then it is a good indication that you have one. The USB loader will still work though so just follow the guide as normal.
    
    When completed you will have everything you need to play backups and the SD card does not have to be left in, you can delete everything off it if you wish.
    
    Make sure you do the steps in the right order or you could run into problems, and read the guide through a couple of times before trying it. Read ALL OF IT! Most problems arise from people not reading the instructions properly or not using a compatible SD card, a plain 2gb one is best. If you are buying a new one try and get a Sandisk.
    
    All you need is an SD card formatted to FAT32, an internet connection on your Wii and these files: DOWNLOAD
    
    Before you start make sure Wiiconnect 24 is off as it can stop bannerbomb working, you may turn it back on once you have completed the guide.
    
    If you get errors during any of the steps format your card with this tool.
    
    TAKE OUT ALL GAMECUBE MEMORY CARDS/CONTROLLERS
    
    
    1. INSTALL BOOTMII AND THE HOMEBREW CHANNEL
    
    a). Put all the files from ‘copy to sd card.rar’ onto the root of the SD Card. It should look like this when done.
    
    b). Insert the SD card into Wii.
    
    c). Go to Wii Options, then go to Data Management > Channels > SD Card, then you will get a message saying "Load boot.elf?" , select 'Yes' and the Hackmii installer will run.
    
    d). Install Bootmii as boot2 if you can, if not then install it as an IOS then go back and install the Homebrew Channel.
    
    The Homebrew channel will ask you to update - say NO!
    
    2. BACK UP YOUR NAND (OPTIONAL)
    
    Making a NAND backup with Bootmii is highly recommended, it will recover your Wii from 99.9% of bricks.
    Use the same SD card you used to install Bootmii and make sure there is at least 530mb free on it.
    Bootmii is very fussy about what SD cards it uses, so avoid generic ones and try and use a Sandisk or similar.
    
    
    a) Put the SD card into the Wii, if you installed Bootmii as boot2 then it will load, if it is installed as an IOS go to the Homebrew Channel, press 'home' on your wiimote and select 'Launch Bootmii'.
    
    b) Use the power/reset/eject buttons to navigate the Bootmii menu and select the icon with the gears on it. If those buttons don't work then you will have to use a Gamecube controller.
    
    c) Now select the icon with a green arrow pointing from the chip to the SD card and follow the on screen instructions.
    
    D) In about 10 mins you will have a NAND backup, it is normal to have up to 80 bad blocks so don't worry if you get some.
    
    e) Put the SD card into PC and copy the NAND backup somewhere safe, you can now delete it from your card. If you installed Bootmii as boot2 then also copy the Bootmii folder to your PC and either delete or rename it, otherwise it will load every time you switch your Wii on.
    
    If ever you get bricked then copy the bootmii folder and NAND backup onto your card, do steps a) & b) again, using Priiloader to get to HBC if necessary, then select the icon with the arrow going from the SD card to the chip. It is not recommended to restore your NAND if you have Bootmii installed as an IOS.
    
    
    3. GET A CIOS
    
    a) Go to Homebrew channel and run Trucha Bug Restorer, load IOS36, press 1, read the warnings then select 'downgrade IOS15', select to load IOS from SD card then let it do its job, keep an eye on what it is doing and make sure you select 'load from sd card' when it asks & don't get any errors.
    
    b) Run Trucha Bug Restorer again, this time select to load IOS15 on first screen using dpad left/right, then select the IOS36 menu & install patched (select 'yes' on all 3 patches) IOS36 to slot 36, again using IOS from SD card.
    
    c) Run Trucha Bug Restorer again, load IOS36 and this time select restore IOS15.
    
    d) Run cIOS38 r14 installer, select IOS36 as the one it should use and then select wad install.
    
    If your Homebrew Channel flips upside down then continue with the guide and when completed reinstall the homebrew channel.
    
    
    
    4. UPDATE YOUR SYSTEM MENU VERSION
    
    Warning - If you don't install the patched IOS60 first you will brick!
    
    This step is optional unless you are on 3.1, 3.3 or 3.4 in which case you must update, if you are on 3.2 or 4.0 you can update if you want and it is recommended that you do, if you are on 4.1 there is no need obviously! If you are on 3.1 you will have to update to 4.0 first, make sure you install the patched IOS60 first though still. Before you update to 4.1 make sure you have at least 250 blocks free or you will brick, install IOS60-patched first with Wad Manager using IOS249, then run Firmware Updater 4.1. If you are on 3.3 or 3.4 then you must update now - DO NOT install priiloader until you have updated as it will cause untold problems!.
    
    
    5. THE FINAL STEP
    
    Priiloader is also an optional install, if you don't want it just skip b & c, but you must do step d, system menu hacks can be taken care of by Starfall (3.2) or startpatch (4/4.1), if you want them click my sig and have a look through my mediafire. There are no system hacks for 3.3/3.4.
    
    a) If you are on system menu 4/4.1 use Wad Manager with default settings (IOS249 & SD card) to install IOS60-patched.wad - make sure you do this before you install Priiloader. If you installed it in step 4 then skip this part. Never uninstall IOS60! You will brick!!
    
    b). Open the Homebrew Channel and load Priiloader, press + to install. After install, your Wii should reboot and load the Priiloader menu. If it doesn't, turn your wii off and on again whilst holding down reset and it will load the Priiloader menu.
    
    c) Select 'system menu hacks' in the Priiloader menu, and enable the hacks that you want - 'skip disc update check' and the region free ones are all you need. Select 'save settings' and wait for confirmation message to display 'settings saved'. Press B to go back, and enter Settings. Set 'Autoboot: System Menu' using D-Pad, then select save settings. Press B to return to main Priiloader menu.
    
    d) In the Priiloader menu select Homebrew Channel (if you didn't install Priiloader then just open HBC as normal), run Wad Manager 1.4, use default settings (IOS249 & SD card) and install these wads from the 'wad' folder:
    
    IOS38-64-v3610
    IOS50-64-v4889
    IOS53-64-v5149
    IOS55-64-v5149
    NeoGamma r8b7
    
    Then restart your Wii.
    
    
    All done! You will now have the safety/hacks of Priiloader & Bootmii, NeoGamma R8b7 backup loader that has 99% compatibility, cIOS249 r14, IOS38, 53 & 55 for newer games and IOS50 to help prevent disc update bricks. If you ever need to access Priiloader's settings hold down 'reset' when switching your Wii on.
    If you get the 'system files corrupted' screen don't panic, just reinstall preloader and if that doesn't fix it reinstall your current system menu with Wad Manager.
    
    UPDATES
    
    If you want to update your cIOS in the future or if you want to install a different one just run the installer and select ios249 as the one it should use, it will overwrite the old one so no need to uninstall. If you want to update Neogamma go to wii options > data management > channels and delete the old one first, then just install the new one with wad manager.
    If you want more hacks for Preloader have a look at them here, and copy/paste them to your hacks.ini file. Make sure there is one blank line at the bottom.
    
    OPTIONAL
    
    Install the new 4.2 shop channel with Wad Manager - Download
    
    Install USB Loader GX & WBFS Manager 3 - Download
    
    Install cIOS56 to play Guitar Hero 5/Beatles from the disc channel - Download
    
    Install the new cIOScorp 3.5 for DVDR loading through Disc Channel - (works on all wiis) - Download - make sure you read the readme!

  2. #2
    Senior Member
    DA KINE WiiHacker
    mauifrog's Avatar
    Join Date
    May 2009
    Posts
    9,180
    Thanks
    307
    Thanked 9,572 Times in 2,972 Posts
    Blog Entries
    15
    When you boot, do you see the health and safty screen? If you do try to hold + and -, the push A a few time while holding.

    Otherwise try savemiifrii, if it works you'll see your system menu in the lower right hand conner. You will need a chip preconfigured to autoboot to use any autoboot disks. You could try to autoboot SSBB ntsc if its in your region, but I doubt it will work.
    Ipsa scientia potestas est.


    Warning: Piracy is NOT supported. Word your questions carefully.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •